Jump to content
SAU Community

Recommended Posts

Hey guys

especially youse with the Yellow stags.

Have you had any issues with paint fading?

I was warned about the yellow not being designed for Aust Conditions and it could fade real easy.

Has anyone had any issues with it. I'm after a manual RS4 yellow preferably with sunroofs and leather.

Cheers Girls & Boys

Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/
Share on other sites

no issues here :) ... except for the painted plastic parts fading faster than the painted metal parts (eg side moulds, dayz tail light covers etc), but its hardly noticeable

but as Logan has previously mentioned, they do surprisingly attract bee's :P

Edited by Brycey
Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/#findComment-3523872
Share on other sites

i have had no issues with the metal bits but have got sunburn on my spoiler where all the clear has flaked off it, and i found that using good old mister sheen stops it for a bit. but as we are on level 4 water restrictions and am not allowed to wash the car it has come back, so i will have to give it another dose soon until i can afford to have it resprayed.

the end covers for the side rear windows are faded too so i am gonna get them done in black so it looks like the windows go all the way back.

so all in all the yellow doesn't appear to fade as much as red which is a good thing.

Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/#findComment-3524648
Share on other sites

Have a talk to Chuckie, his car has been in WA for about 18 months, didn't see any issues with the paint the other night.....(I swear that the yellow is even brighter at night).

I don't think that you will find an RS4S (manual) with leather.... they come with a different interior cloth of their own. It is similar to the Autech cloth and also similar to the GTR in texture.

It's a woven polyester...

The only way that you'd find a leather interior is as an option, ('cept I don't think it even came as an option) or by finding an auto that's been converted... (careful!!).

Yellow is also an S2 colour only.... be prepared to pay a premium for the RS4S. Allow about $20,000 all up, you should be able to find a good one, as far as I have seen they are still selling over the Million yen mark.

Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/#findComment-3525063
Share on other sites

Hey guys

especially youse with the Yellow stags.

Have you had any issues with paint fading?

I was warned about the yellow not being designed for Aust Conditions and it could fade real easy.

Has anyone had any issues with it. I'm after a manual RS4 yellow preferably with sunroofs and leather.

Cheers Girls & Boys

If you mean suede when you say leather, this is the standard trim for a manual.

If you mean normal shiny leather you'll have to get them changed...

Just so you know what you're up against approx 6-7% of c34's are factory manuals

of those approx 85% are 4wd and about 1% of those have sunroofs you can imagine how many of those are yellow...

Good luck with the search!

These are approximations feel free anyone to make corrections :(

Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/#findComment-3525107
Share on other sites

As mentioned the only problems ive had with the yellow are the fact that the bonnet and plastic parts fade faster than the rest of the car.

Car still looks good though!

Ive also had trouble with the clear coat coming off my bonnet :), although i think this may be due to the product i have been using on it rather than the paint quality.

Theres currently a handful of yellow stageas for sale in NZ, however, none are manual :(

Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/#findComment-3525357
Share on other sites

YELLOW MISTER SHEEN IS THE BEST,i have been using it for 27 years & haven`t found anythink that come`s close.more to the point no worries with the yellow paint.I have started using AUTOGLYM bodywork shampoo conditioner which is very good,WASH & MISTER SHEEN every week.thank`s chuckie.

Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/#findComment-3527326
Share on other sites

YELLOW MISTER SHEEN IS THE BEST,i have been using it for 27 years & haven`t found anythink that come`s close.more to the point no worries with the yellow paint.I have started using AUTOGLYM bodywork shampoo conditioner which is very good,WASH & MISTER SHEEN every week.thank`s chuckie.

Mr. Sheen contains silicon = Bad Idea...

Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/#findComment-3529270
Share on other sites

  • 2 weeks later...
Mr. Sheen contains silicon = Bad Idea...

WELL as i said i have been using it for 27 year`s with no worries,with regard to fade the worst is the wingmirror`s.The mister Sheen dose it all glass,wheel`s,plastic.head ???.wax&grease remover silicon GONE = GREAT IDEA.CHEER`S chuckie.

Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/#findComment-3551301
Share on other sites

with regard to havin any paint rework done all you need to say to the repairer is that you have used a silicon based product and they put these wonderful little things called "silicon drops" into the paint mix and viola all good!

i ahve not had any issues before with repairs etc once ive told em i use mr sheen etc on my paint work.

i have been using it on bikes and cars for the last 20 years after i started using it on my motorcross bikes when i was 15 to keep the plastics looking good, keeps bugs from sticking as hard too, and with the prevelence of water restrictions it is a godsend cos when it finally does rain i can get out in it with a sponge and give it a wipe over and pretty much clean,save for heavier stuff it requires a bit of soapy stuff and all good.

Link to comment
https://www.sau.com.au/forums/topic/196996-yellow/#findComment-3551571
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...