Jump to content
SAU Community

Recommended Posts

Hi guys,

thinking about getting my ecu remap from one of the member here, but can't remember who ??

can anyone point me to the right direction or recommend the guy who the member here to do the job

cheers

dr dift does em, and hes a member.

havnt used him yet.

but will be going down dat path

r33 ecu just needs a daughterboard soldered to it to fit the rom/emulator

r32 can be rechipped without an additional daughterboard and can be made to work in an r33 i.e. switch 2 inj wires and add the r33 vq maps etc. - feedback loops are all crazy but?

Many people have asked to me about R33 remap.

Thank you

OK.

When your car has been boosted up (normally over about 12psi but some cars only 7-11psi.) with air flow meter being near 5V, RB25det ignition timing map will retard.

As a result, engine misfire and engine cut will be experienced.

I have three remapping options

1) REMAPPING FROM DYNO SHEETS AND CAR MODs.

After receiving your dyno sheet (I need AFR and rpm) I will remap chip accordingly and send it to you. Original chip will be replaced with remapped chip on ECU.

As soldering 84pin chip is difficult, you probably need to find a soldering ship. eg; TV and video repair shop.

Or, I could fit remapped chip to my spare ECU then exchange it with yours.

Also I could fit remapped chip to your ECU.

*please check on dyno again when you get the chip to ensure safety.

*Please Check and adjust ignition timing, AFM (many cars fault), O2 sensor before dyno.

Advantages

Able to remap in all states.

Obvious increase in power.

If your car becomes too lean or pings after fitting my chip, I will make another chip.

Disadvantages

I’m able to remap up to intercooler, bigger turbo, fuel pump, Z32 AFM.(I can not remap to full tune engine.)

You will pay dyno fee 2 times.

Dyno shop may charge for checking and adjusting ignition timing, AFM (many cars fault), O2 sensor before dyno

Price chip only from $350 (std turbo)plus post

Exchange from $400 plus post

2) REMAPPING ON ROAD

I will fit wideband air fuel ratio meter, and rap top computer, modified ECU for real time remap, emulator and map tracer.

We (you and me) will go for a road test then I will remap ECU real time.

Advantage

Remap will be adjusted to real driving condition. (Its real load and window for intercooler.)

You’ll be able to recognize an obvious difference in feel when driving

Free checking and adjusting of ignition timing, AFM (many cars fault), O2 sensor

Cheaper price than dyno tune.

Disadvantages

If you are provisional driver may be dangerous.

You can not see exact power increase

If your car has a lot of power I can not road tune-danger factors

Price from $450(std turbo)

3) DYNO TUNE

Advantage

You’ll be able to see exactly, how much power increase.

Safer than road tune. (No accidents and no police)

You do not need drive.

Free check and adjust ignition timing, AFM(many cars fault), O2 sensor

Disadvantages

You can not check drive feel.

You will pay tune fee and dyno fee.

Price from $500 plus dyno fee(std turbo about1- 2 hours $90-180)

I tuned his car about 3years ago on the road.

His car made 196Kw at 8psi.

http://www.skylinesaustralia.com/forums/R3...ml&hl=toshi

Edited by Toshi

Power will increase about 15-20kw.

Some cars over 30kw more. (FMIC is very important)

This is R33 A/T dyno sheet.

33kw more.

(red) Std boost (7.4psi) std ECU.152kw

(green) Std boost (7.4psi) my chip.abou 170kw

(blue) boost 11psi my chip. 185kw

http://users.tpg.com.au/yuna/dyno%20kw1.jpg

flash-tune of a factory ECU only makes sense if you never plan to mod your car again

by saying that - I'd be taking my pride n joy to a well respected tuner with aftermarket ECU :banana:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...