Jump to content
SAU Community

Recommended Posts

Hello,

I think this might be my first post but any way i have problems :D

The car taking ages to turn over when cold and not as long when hot. When its cold it takes many pumps of the pedal and 2 or 3 turns of the key as to not kill the starter.

When the car is hot its the similar but doesnt need as much pushing of the pedal to fire.

I changed the spark plugs thinking that it might be them....but no

Changed the fuel filter....but no.

Tried taking air-filter off to start car....but no.

The car doesnt feel down on power so not the fuel pump? it's only a starting issue.

Don't know what else i can try? so im looking for suggestions.

The car does have a Mines ECU (which i was stoked to find) but it hadnt effected the starting before. Also has a 3 inch off the dump pipe, CAT and a choking blitz muffler on the back. Other than that, it's stock.

It's been a couple of weeks like this now.

Im after any ideas any of you might have.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/198298-2000-stagea-s-tune-starting-issue/
Share on other sites

cold days/nights my car is the same, doesnt fire, plugs are fine etc, everything has been serviced, hot days its fine. New pump will go in soon and will be checking fault codes when the informeter arrives... let me know how you go. I didn't gap my plugs down, could that be it?

Now winter is over i have no probs :D

Edited by Ryan1600

when i first got my car i had heaps of problems getting her to start to the point it would take you 5 or 6 pushes on the pedal while you were trying to start it to actually get it going.... my problem was the fact the compliancer had run her out of petrol...2 or 3 weeks later when i had good fuel in her she was fine...now 12months down the track still no problems at all *crosses fingers*

when i first got my car i had heaps of problems getting her to start to the point it would take you 5 or 6 pushes on the pedal while you were trying to start it to actually get it going.... my problem was the fact the compliancer had run her out of petrol...2 or 3 weeks later when i had good fuel in her she was fine...now 12months down the track still no problems at all *crosses fingers*

I keep mine over half a tank with 98 or 100RON

You shouldn't be pumping the pedal on ANY fuel-injected car when you're starting it - it's all controlled electronically, so there's no need for you to try and add more fuel to get it started. This might be part of the problem.

Also, have you checked the small in-line fuel filter near the tank? That often gets clogged first as it's the nearest filter to the tank, so have a look to see if there's anything blocking it.

Oh, and like Kirstie, I never let my fuel level drop below a quarter tank - when the level gets that low there's more of a chance that it the pump will pick up all of the crap that sits on the bottom of the tank, and then your filters will get clogged more quickly.

You shouldn't be pumping the pedal on ANY fuel-injected car when you're starting it - it's all controlled electronically, so there's no need for you to try and add more fuel to get it started. This might be part of the problem.

Also, have you checked the small in-line fuel filter near the tank? That often gets clogged first as it's the nearest filter to the tank, so have a look to see if there's anything blocking it.

Oh, and like Kirstie, I never let my fuel level drop below a quarter tank - when the level gets that low there's more of a chance that it the pump will pick up all of the crap that sits on the bottom of the tank, and then your filters will get clogged more quickly.

on a cold day, pumping is the only way to start it, could be TPS? Also primed the pump a few times before starting, doesn't make a difference

pumping the pedal - yeah.. not a good idea on an EFI car. the only time you should be screwing with the accelerator on startup is if you think the car is " flooded" with fuel .

opening the throttle body butterfly valve will allow more air inside and hopefully get rid of some of the excess fuel vapours and also allow a bit more air in there so that the mixture will eventually fire.

have you tried changing the heat range of your plugs? ie go hotter or colder?

what do the plug tips look like when you take them out .. can you show us a pic?

can you hear the fuel pump prime?

is the edge of the butterfly valve in the throttle body clean? or is it gunked up?

from what I understand ( least on sr20's / my RB knowledge is still on a learning curve) there is a small pin hole that lets a bit of air past hte butterfly valve on idle - and maybe check your idle air control valve? they sometimes get gunked up and need a clean

where exactly is that filter?

Some EFI cars have them, not all - haven't checked the Stagea, so I don't know if there is one there or not. It's usually in the line just after where the fuel lines come out of the tank. My old man's Camry (from way back when) had one that got clogged on the way down to Melbourne one year which had him scratching his head for quite a while until it was pointed out by someone else.

I've seen it on a few cars, but I couldn't confirm if the Stagea has one or not as I've never checked for it.

or if you dont want to get the fuel injectors cleaner you can pump United fuel Boost 98 which is able to clean the lines cos of the ethanol added into it. Im using boost 98 most of the time. If i have the coupond fuel vouchers i will use it.

pumping the pedal - yeah.. not a good idea on an EFI car. the only time you should be screwing with the accelerator on startup is if you think the car is " flooded" with fuel .

opening the throttle body butterfly valve will allow more air inside and hopefully get rid of some of the excess fuel vapours and also allow a bit more air in there so that the mixture will eventually fire.

have you tried changing the heat range of your plugs? ie go hotter or colder?

what do the plug tips look like when you take them out .. can you show us a pic?

can you hear the fuel pump prime?

can hear it prime, then stop, turn acc off, then back on to reprime... When i pull everything apart to clean it, any directions as to what i am cleaning, what to use to clean it, and can i stuff any adjustments whilst doing it?

-Ryan :D

Fuel pump switches off once there is pressure in the system and the engine is not running so no need to keep pumping to maintain pressure. Switching it on and off multiple times won't make any difference, the fuel system is either pressurised, or not... Happening when it's cold suggests it might be a sensor playing up... Check error codes would be a good start.

well I dont know for sure..( as I have only cleaned the IAC valve on the pulsar ) but I would assume the same thing applies to the RB motors.

what do the sparkplugs look like? is the colour ok ?

can hear it prime, then stop, turn acc off, then back on to reprime... When i pull everything apart to clean it, any directions as to what i am cleaning, what to use to clean it, and can i stuff any adjustments whilst doing it?

-Ryan :D

Update....

I know you're not supposed to pump the pedal, but if i didnt it would probly just crank all day and not fire. Sometimes it will start first go but rarely.

It feels like its starting to lose some down low power, but is almost as fast at hight revs 4500+

Can't hear fuel pump prime, ive never been able to hear a stock fuel pump prime in any car.

Is it possible the fuel pump could be dying? A mates sprinter would start but stall past 3000rpm = stuffed fuel pump. Another mates silvia would lose power at 5000rpm and stall pretty much = stuffed fuel pump again.

But mine not getting fuel at start up = stuffed fuel pump?!?

A dirty/rooted O2 sensor do it?

The plugs that i took out of the car, the tips were white possibly too hot?. not fouled and black.

I might check out the throttle body tomorrow, when i did the plugs there was some black shite (oil/dirt) on the cooler piping inner walls. I just assumed it was a crud build up.

Thanks for your suggestions. :P

Edited by Whooby
  • 3 weeks later...

Update:

Tried a larger fuel pump, good for up to 500HP - No change, bit too much fuel for a stock engine.

Could it be a crank angle sensor perhaps? once the engine fires there is a Tick Tick Tick then stops. Not sure what it is yet.

Any help please :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
×
×
  • Create New...