Jump to content
SAU Community

Recommended Posts

The following R33 parts...

Greddy intake fit to neo?Yes

Clutch for fits to neo?No, same as late 32/33 gtr

Forged pistons for r33 fits to neo?No

Exhaust manifold fits to neo?yes

Nissan OEM gasket kit fits to neo?should

That's all :P

Edited by Adriano
Greddy intake manifold needs to be modified..not a perfect fit

bolts straight up perfectley with no mods, wiring and shite needs mods.

http://www.skylinesaustralia.com/forums/In...eddy+plenum+r34

http://www.skylinesaustralia.com/forums/Gr...=plenum+r34+gtt

And another question...

I would like to put wisecos because they are cheap..

What compression I will have with stock headgasket with

R33 RB25 pistons?

RB26 pistons?

Here there are the spec of the pistons... I don't know how to calculate the ratio so anyone how knows please let me know!

http://www.wiseco.com/PDFs/Catalogs/SC08/N...aruToyotaVW.pdf

And another question...

I would like to put wisecos because they are cheap..

What compression I will have with stock headgasket with

R33 RB25 pistons?

RB26 pistons?

Here there are the spec of the pistons... I don't know how to calculate the ratio so anyone how knows please let me know!

http://www.wiseco.com/PDFs/Catalogs/SC08/N...aruToyotaVW.pdf

Neither are appropriate, you will end up with >10:1 comp.

R34 neo throttle body is basically the same as r33 except it has the TCS butterfly on the front, no probs fitting a Q45 one to the greddy. IMO save the $1300 for the greddy/Q45 and do the motor properly, maybe with an rb30(then you can just use rb30ET forged pistons to give you high 8's:1 comp)

Edited by Adriano

Anyone know what pistons I can put to NEO??

Wiseco don't have neo pistons?

EDIT

Adriano are you sure? In this post they say Abo Bob said that will be 8.75:1!

http://www.skylinesaustralia.com/forums/Rb...rged&st=20#

RB25 and RB26 aren't different high pistons? Who knows to calculate the compression? Always with stock gasket!

For both 25 and 26 pistons!

Edited by GreeceS13

NEO has a smaller combustion chmaber so R33 pistons will produce a high ( as in too high ) a comp ratio.

Exhaust manifold is the same stud pattern.

OEM gaskets - some will be different, like valve stem seals etc - but most should be same as R33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
×
×
  • Create New...