Jump to content
SAU Community

Rda Rotor (& Ebc Pads) Group Buy Is Back In 2008!


Recommended Posts

Quote sent..

Time to close the Group Buy 33 orders:

1. Mr Moo (payment cleared)

2. MotoMan (payment cleared)

3. daemon667 (payment cleared)

4. bombtrack (payment cleared) ** Secured the last pair of the first 4 pairs available for front R34 GTT rotors **

5. Madaz (payment cleared)

6. Jet-25L (payment cleared)

7. Kah Chong - RX8 (payment cleared)

8. WRRR (payment cleared)

  • Replies 548
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

If there are still enough interest here from R34 GTT owners to get slotted rotors, I'm sure I can get RDA to keep making them out of R34 GTR front...

You're welcome. I'm not doing brake hoses at the moment. I think Al started that a few years ago with MalTech in Geelong with quite good prices for R32/R33/R34 range, I'm not sure if he's still doing that. Just do a search on the group buy section for braided hose and/or Maltech.

got mine today and installed. after harassing tnt for not knocking loud enough and walking of straight away yesterday, by the time i got to the door he was in his truck and drove off.

but very happy with your service (not your fault there drives lazy)

You're welcome, yeah TNT won't call even when you put the phone on the delivery docket. And I've missed my delivery a few times that way too.

At least they'll leave a calling card.

If you want the R34 GTT rotors in dimpled patern it will be in normal stainless finish, just like the standard slotted one. The reason is there's nothing out from factory with 310mm size, so what was done is RDA will machine the 324mm rotors from GTR down to 310mm, balance it, and put either slotted or dimpled pattern as you wish. However it will not have the gold anodised finish.

Problem with that is if you want to get the rear in dimpled, the rear will come in factory gold anodised finish. So your car will be quite colourful front to rear - if you have no problem with that.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...