Jump to content
SAU Community

Recommended Posts

There is so much stupid retarded stuff its not even funny.

protein is for muscle development, too much will increase inflamation

carbohydrates is for energy, too much will decrease the release of ATP

unless your joiced up, the only form of maxing hypertrophy is by:-

1- full body work outs involving compound weights (squats, bp, dl,pu etc) all weight lifting should involve barbells

2- to increase recovery should not plateu, always leave 1 rep in the tank, also decrease the risk of injury, workouts should last 45m to 1hr

3- Diet is part of building muscle, eating the right amount of protein and/or carbos at the right time is the key, http://www.youtube.com/watch?v=b4pEcB5jWRI...feature=related this is just an example, there is nothing wrom with the mediterranean diet, nothing wrong with raw eggs.

4- psychological aspect, determination, disciple and dedication, remember the three D's.

There is a lot more depth for these four points but you get the picture, olympian weight lifters dont do and dont heat 90% of the junk on this thread.

Edited by 2lazy
You wanna know what the real problem is in here? A small number of the posters posting in here, frequent the fitness section on NS.com. Over there, the majority of the regular posters are powerlifters, and many of them train at PTC in Frankston under Markos. There's no problem there, and anyone who does read the NS.com fitness section would know that there are some strong guys training there and achieving, as far as what they're after, great results.

The problem is that these same guys, have little to no respect for anyone who doesn't train purely for strength. They mock pretty much everyone else who's mantra isn't squat/dead/MP and eat. The typical topless guy at summadayze etc, they laugh at.

Any weight lifter mocks bodybuilders because they build definition when they dont have any mass to build, does that make sense?

Mass then definition.

:banana: Why are you going to the gym if you are not training for strength??

Any weight lifter mocks bodybuilders because they build definition when they dont have any mass to build, does that make sense?

Mass then definition.

:banana: Why are you going to the gym if you are not training for strength??

I said 'purely' for strength. Some people enjoy looking good as well...

Looking good like what? You mean fit?

Everyone has their own reasons for training, sure strength is an aspect but not its not the only reason for many people.

sense of achievment, confidence or just simply enjoy trying to better yourself and end joy the excersise. Perhaps just enjoy what you do and let others do the same without trying to seem superior.

Edited by gersfan

You are sounding a bit "heil Hitler" there 2lazy. That's the problem with lifters, they can't see any reason to be at the gym other than to get stronger. Body builders are just as guilty when they pay out on people for not exercising every muscle in their body or chasing definition.

You wanna know what the real problem is in here? A small number of the posters posting in here, frequent the fitness section on NS.com. Over there, the majority of the regular posters are powerlifters, and many of them train at PTC in Frankston under Markos. There's no problem there, and anyone who does read the NS.com fitness section would know that there are some strong guys training there and achieving, as far as what they're after, great results.

The problem is that these same guys, have little to no respect for anyone who doesn't train purely for strength. They mock pretty much everyone else who's mantra isn't squat/dead/MP and eat. The typical topless guy at summadayze etc, they laugh at.

Now, I've been to summadayze, KMG, Future etc, and we all know there's plenty of guys there with their shirts off, some even train specifically for these events, so that they can get their shirts off and pick up, or just look good (in their opinion) in general.

To be honest, from what I've seen on NS.com, the bodies aren't something I'd aspire to personally. They might be capable of squatting/benching/military pressing and dead lifting big numbers, but from an aesthetic point of view, they're not what I and many others are after.

Now, no one is saying that they're wrong to train the way they do, but that doesn't mean that how they train is RIGHT, and how anyone else trains is WRONG. I'd much rather look like the typical 'gear head from summadayze' than the typical powerlifter on NS. They'd all laugh at that, and they do, the only problem is some people take it to heart, whereas I couldn't give less of a f**k what someone else thought of my goals if I tried.

Agreed, this is what I was getting at when I talk about people thinking there's only one way about achieving results, when everyone has different goals. Some of those PTC newsletters...it's pretty disgraceful the lack of respect the writings show for anything but what they do.

Yep, and the section is actually starting to go downhill because of it (although as far as they're concerned it's perfect as it's squat/deadlift/bench/MP or f**k off) Opinion is no longer allowed if it differs from theirs. Pretty sad really.

Yep, and the section is actually starting to go downhill because of it (although as far as they're concerned it's perfect as it's squat/deadlift/bench/MP or f**k off) Opinion is no longer allowed if it differs from theirs. Pretty sad really.

I am speaking from experience, you either take it for free or you dont, you provided a vague explanation on what you want to do, and i still dont understand what you mean by fit, skinny? med? cut?

Whats funny is you actually get someone that knows what hes talking about and nobody wants to listen.

You are sounding a bit "heil Hitler" there 2lazy. That's the problem with lifters, they can't see any reason to be at the gym other than to get stronger. Body builders are just as guilty when they pay out on people for not exercising every muscle in their body or chasing definition.

Agreed, this is what I was getting at when I talk about people thinking there's only one way about achieving results, when everyone has different goals. Some of those PTC newsletters...it's pretty disgraceful the lack of respect the writings show for anything but what they do.

Yeah Markos is not good with words sometimes but he means well, I dont agree with not wearing a belt, if your not wearing one I sugestt a spotter.

Its up to you, you want to achieve a goal in 2 years that can be done in 1 be my guest.

People are happy to listen to experienced experts but you have to be able to listen to them too instead of just telling them their way won't work, or won't work as fast as yours. There is more than one expert in this thread, and again, everyone's goals differ so widely that you cannot tell me what I want to achieve will be done in 2 years under my instruction where you could do it in 1 year. You have no idea what my goals are so you can't make that assumption that your S/D/B workout is going to get me my results faster. These basic compound exercises are not key to everything. Take for example, I could be a runner who goes to the gym and wants to exercise only legs and cardio...no heavy upper body so as to save on dead weight up top. Following the S/D/B "key to any regime" exercises is going to f*** me over - I will have to customise that program so much that not much of the S/D/B workout is still going to be key.

I think the advice to stick to big compounds is given assuming a young male wants to get bigger, leaner, stronger and so on. All you need to do is tweak your diet. I'd say 90% of guys who train want to get bigger and leaner. Those who say they are happy to stay lean and small, lie, they want to get bigger. Those who say they are happy bulky and big, lie, they want to get leaner. Those in the middle are rapt lol. Obviously if you want to be a marathon runner or a swimmer, muscle mass isn't a big factor, then your training would deviate from standard bodybuilding and powerlifting compound movement techniques.

I think the advice to stick to big compounds is given assuming a young male wants to get bigger, leaner, stronger and so on. All you need to do is tweak your diet. I'd say 90% of guys who train want to get bigger and leaner. Those who say they are happy to stay lean and small, lie, they want to get bigger. Those who say they are happy bulky and big, lie, they want to get leaner. Those in the middle are rapt lol. Obviously if you want to be a marathon runner or a swimmer, muscle mass isn't a big factor, then your training would deviate from standard bodybuilding and powerlifting compound movement techniques.

Exactly, that was my assumption... but yeah a marathon runners workout is different from a sprinter.

Hey just to lighten the mood I thought I'd tell you about my experience with booze and weight loss/gain.

I had a check up in November last year when I was using some (legal) sups which can affect cholesterol. I have a history of heart disease so my new doctor wanted a full medical done.

Anyhow, one of the tests was a liver function test. A bit of back history, I'm not a regular drinker (a glass or wine or a beer a few times a week), I'm more of a binge drinker and it would be maybe 3 weekends a month or less but when I did drink, I'd put away a shit load with the boys.

Anyhow, personally I'd always find I carry extra weight after a BIG weekend on the booze. At maximum up to 3kg!! No doubt this was extracellular fluid which is typically cause by irritation/infection.

My liver function test came back with results out of the normal so my doctor wanted me to go booze free for 2 months for a follow up test which happened to fall over Christmas/NYE - no way that was going to happen.

I've been booze free for 12 weeks this weekend and have had my follow up test done and it's now perfect, as is my cholesterol @ 3.3. The BIG difference is weight loss though, I've shed a large amount of body fat, and not the easy stuff, I'm talking the really stubborn belly and love handles. I'm now starting to see a 6 pack etc!

I never would have realised how much of a difference booze makes to weight loss. Sure I understand the livers role in fat metabolism and the effects alcohol can have but I never realised just how much difference it makes. I can now eat much more junk and still stay trim, even loose weight! Wish I had of tried this earlier :yes:

Just thought I'd share because I see a lot of guys slogging it out gym then hitting the booze hard over the weekends eating up all that hard work!

i dont agree with wearing a belt, only because i like to apply things from the gym into real world applications.. so id prefer to build up lower back strength as you dont wear a belt when your not in the gym... therefore.. your pure strength routine maybe working your major muscles.. your supporting muscles may be lacking.. and your only as strong as your weakest muscle.

i agree that alot of people are vein.. they want to look different.. they want to be big like that guy.. or be ripped like that guy.. or have arms like that guy... they will never be happy.. and they may be a good thing.. they will strive to keep trying and that can only be a good thing... until the motivation is lost because.. i think its better to accept your body shape.. and do the best with what youve got.. dont get depressed, because you will have something that they dont.

its always been an age old battle between the body builders and the strong guys.. how do you judge whos better??? do you judge someone by the intensity of the workout.. or by the weight they lift?? or by the size they are?? do you mock the little guys?? even if they are lifting the same ratio of weight to body weight as you are?? be honest..

id like to ask a serious question..

im happy with the development of my hammys... im happy with the thickness and width of my hammys... but my quads are lacking.. especially in the width part.. and mainly the inner part... so ive been thinking of doing front squats, but the weight that i can squat.. my chest and arms cannot hold.. it sits on my collarbone and feels uncomfortable, but with the weight that i can hold, id have to do a gazillion reps to feel that illustrious burn we all strive to achieve..

thoughts?? any other leg moves you guys have found that use your quads more than the hammys.. pure freeweight workout, no machines.

Hey just to lighten the mood I thought I'd tell you about my experience with booze and weight loss/gain.

I had a check up in November last year when I was using some (legal) sups which can affect cholesterol. I have a history of heart disease so my new doctor wanted a full medical done.

Anyhow, one of the tests was a liver function test. A bit of back history, I'm not a regular drinker (a glass or wine or a beer a few times a week), I'm more of a binge drinker and it would be maybe 3 weekends a month or less but when I did drink, I'd put away a shit load with the boys.

Anyhow, personally I'd always find I carry extra weight after a BIG weekend on the booze. At maximum up to 3kg!! No doubt this was extracellular fluid which is typically cause by irritation/infection.

My liver function test came back with results out of the normal so my doctor wanted me to go booze free for 2 months for a follow up test which happened to fall over Christmas/NYE - no way that was going to happen.

I've been booze free for 12 weeks this weekend and have had my follow up test done and it's now perfect, as is my cholesterol @ 3.3. The BIG difference is weight loss though, I've shed a large amount of body fat, and not the easy stuff, I'm talking the really stubborn belly and love handles. I'm now starting to see a 6 pack etc!

I never would have realised how much of a difference booze makes to weight loss. Sure I understand the livers role in fat metabolism and the effects alcohol can have but I never realised just how much difference it makes. I can now eat much more junk and still stay trim, even loose weight! Wish I had of tried this earlier :yes:

Just thought I'd share because I see a lot of guys slogging it out gym then hitting the booze hard over the weekends eating up all that hard work!

without going into it too much... basically... when you consume alcohol.. your body goes into code red.. it wants it out... so it shuts down as much as possible to get to work on getting the alcohol out of your system... this includes shutting down your digestive system.. so everything youve eaten gets put on hold, and not digested properly.. it also means you are incredibly hydrated, but not with water, so you are actually dehydrated.. so your body attempts to store as much water as possible because it doesnt know when it will get water again, it stores it around the belly area..

im not a drinker.. and i personally dont understand why people drink so much.. and when you throw smoking into the mix.. it just baffles me..

and these people look at guys like us weird because we take supplements.. otherwise known to them as "steroids"

I don't think you realise it's not that bigger deal until you actually stop drinking for a while to be honest. What I found amazing is when I went out to Pubs etc for parties people would look at me really weird when I said I wasn't drinking, like there was something wrong with me and drinking was the normal, not vice versa. Made me realise just how much of a drinking culture we actually live in.

yeh i definatly get that alot.. theres something wrong with me because i dont drink... and theres something wrong me with me because i prefer to breath clean smoke free air...

wierd wierd crazy people eh!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...