Jump to content
SAU Community

Recommended Posts

OK some questions and feedback from me this morning.

-

OK now for questions.

- When doing Barbel Rows, As my goal for that exercise is more about my shoulder blades I have started bringing it up to the chest, which forced me to drop a few kgs off the bar. Can anyone see any issues with that?

- I do a bit of ab work in my routine, 3 sets of 50 crunches and 3 sets of 70 reps of an air bike/leg scissor type thing. So I have OK looking abs so long as I tense them and hold them in place. If I fully relax, I look 2mths pregnant and my stomach bulges out a small amount. Is this a sign of poor internal ab strength or weak core or is it just that every photo you ever see of someone posing they are flexing their stomach? My partners stomach does not do this and she doesn't have my ab definition or strength and doesn't do any special ab work (she's a runner). I sit all day so that might be it, relaxed abs all day though she does too? I don't think my body fat % is high as I've always been a leaner guy (I'm only 81kg at 6ft). She did say that from an early age she always held her abs in place and has good posture.

Thoughts?

Barbell rows. If you feel the muscles being worked that you are targeting stick with that. Dropping the weight for good form is a win.

Personally I prefer one arm dumbbell rows. Good form will allow a slightly better ROM . Also, with a manageable weight you can focus on getting angles that are more natural for the body mechanics. Always start them with the weakest arm.

Abbs.

Posture is the first thing. Stand up straight , imagine you are pulled up by a rope attached through the top of your head. Some of the 'gut' will disappear. Poor posture does wonders. Work on sitting up straight and standing straight, it will workout the core. When you start out you won't be able to maintain posture for long before you fatigue believe it or not. Over time it will become normal.

Core strength. The Abbs are a bunch of muscles including ones you can't see. They also work with your back muscles. Your abb workout is not building any extra strength, just muscle endurance. However growing the abbs alot will cause them to stick out more too, although you will need to grow them alot for that. Power lifters and body builders can have a muscle tummy look depending on genetics. This is not your problem.

Perhaps you are still fatter than you think.People carry fat differently. Lean is a relative term. Being skinny isn't ripped. You may carry some pudding in the middle over the top of the abbs as a layer.

I have lots of developed abb muscle from back in the day. I can see most of it, including all the little muscles of the obliques without flexing. However , in my view I am far from the 'lean' physique I had. I've got some pudding on the lower part of the obliques and over the top of the abbs.

Lastly, the technique for shifting it is simple but, not easy. Shifting the last of the abb fat is all diet. Mostly , what you can't eat or drink.

Edited by rev210

Much obliged.

I concede there is definitely some fat over the top but I honestly thing it's fairly minimal (can post no homo pics if needed), that's not what worries me though as I tend to prefer to eat and drink what I want, like a boss, and that's part of why I exercise, so I can enjoy myself relatively guilt free.

That said the bigger issue for me is if the bulge (it looks like I'm bloated if you get me not fat as in cellulite just bloated) is more of an inner ab strength thing, and it sounds like it is. Is standing up straight and holding my stomach in using my abs enough to minimise that?

It certainly seems to work for my missus but she talks about how she is not using her exterior (visible) abs to do this where as I feel like I am. She seems to refer to some magical inner ab feeling that I don't think I've felt. When I hold my stomach in I'm using my exterior abs and good posture to do it, if that's what you mean then I can do that.

There's a lot of factors involved in your abs being obvious:

- Body fat. Skinny guys can have six packs without doing a single sit up. Depending on how much muscle you have, 81kg at 6ft may not be all that lean. I'm 6'3 and I checked in at 79kg the other day...I'm not exactly lacking for muscle, so my body fat is low enough that my abs show when untensed. Cardio and diet.

- Ab exercise. If your abs don't feel like big ice cubes when you're tensing them, you probably haven't built them up enough. Sit ups are great but there are a lot of other exercises that build up the abdominal wall. Do you do: tricep pushdown, lat pulldown / chin ups, seated row, deadlifts, woodchops, machine crunches?

- In a lot of photos, people are tensing their abs.

- When sitting down, what little skin and fat you may have folds over your abdominal wall so they will always be less obvious here than standing

- After a big meal or protein shake your stomach will protrude out in it's natural resting state. Abs will always look better first thing in the morning, when your stomach is empty and your muscles have returned to a firm and fresh state.

- Posture. Shoulders back, chest out = stomach in.

There's a lot of factors involved in your abs being obvious:

- Body fat. Skinny guys can have six packs without doing a single sit up. Depending on how much muscle you have, 81kg at 6ft may not be all that lean. I'm 6'3 and I checked in at 79kg the other day...I'm not exactly lacking for muscle, so my body fat is low enough that my abs show when untensed.

- Ab exercise. If your abs don't feel like big ice cubes when you're tensing them, you probably haven't built them up enough. Sit ups are great but there are a lot of other exercises that build up the abdominal wall. Do you do: tricep pushdown, lat pulldown / chin ups, seated row, deadlifts, woodchops?

- In a lot of photos, people are tensing their abs.

- When sitting down, what little skin and fat you may have folds over your abdominal wall so they will always be less obvious here than standing

- After a big meal or protein shake your stomach will protrude out in it's natural resting state. Abs will always look better first thing in the morning, when your stomach is empty and your muscles have returned to a firm and fresh state.

Yeah I know, I used to be 65kg and had awesome looking, zero work, abs lol.

I wouldn't say ice cubes but pretty firm and pretty visible when tensed, it's the fact that when not tensed they disappear as my stomach protrudes out a bit, as if I've just eaten a big meal as you mentioned.

From that list, only deadlift, and that's the stiff leg variety as my hamstring flexibility is poor.

I'll try keeping my core tensed and posture good and see what effect it has over the next few weeks. I'm too much of a fooder to cut out heaps of things from my diet :D Shit, maybe I am just fat, starting to sound that way.

If I take some tensed/untensed photos for review am I gonna have to endure 3 pages of bullshit about how pale I am, how my chest isn't hairy enough, biceps too small blah blah or are we all reasonably good at staying on topic and just telling me my core needs work and my body fat % is too high?

Edited by ActionDan

Dan - try adding "PLANKS" to your Ab routine.

Youtube will have instructions if you don't know what I'm talking about.

Tangles - I pretty much eat that way throughout the weekdays (during work)

easiest thing to do.

Step one - cook up some animals

post-343-0-16524400-1329785142_thumb.jpg

Step 2 - buy salad shit from shops (I get Coles BBQ Salad bag and tomatoes and cucumber and avocado)

freshexpress.jpg

Step 3 - empty half a bag in to big container, throw in tomato and cucumber and avo

Step 4 - heat up some of the animal you cooked and cut up and put in in the salad

Step 5 - add dressing (Optional)

Backup option (if you haven't cooked enough animals) is Tuna with the above.

Looks like this.

post-343-0-69065100-1329785375_thumb.jpg

then 15 minutes later

post-343-0-50820400-1329785394_thumb.jpg

I eat 2 of these during the day at work (easy going office job)

Outside of that I have my cereal at home and dinner in the evening.

Easy as.

Edited by GTST

Yeah I know, I used to be 65kg and had awesome looking, zero work, abs lol.

I wouldn't say ice cubes but pretty firm and pretty visible when tensed, it's the fact that when not tensed they disappear as my stomach protrudes out a bit, as if I've just eaten a big meal as you mentioned.

From that list, only deadlift, and that's the stiff leg variety as my hamstring flexibility is poor.

I'll try keeping my core tensed and posture good and see what effect it has over the next few weeks. I'm too much of a fooder to cut out heaps of things from my diet :D Shit, maybe I am just fat, starting to sound that way.

If I take some tensed/untensed photos for review am I gonna have to endure 3 pages of bullshit about how pale I am, how my chest isn't hairy enough, biceps too small blah blah or are we all reasonably good at staying on topic and just telling me my core needs work and my body fat % is too high?

Post up some pics of your stomach (nohomo), resting/relaxed and tensed, then we can judge (strong nohomo) from that better than speculating based on what you describe. Highly recommend woodchops before you do your situps...they will work your abdominal wall and obliques, creating some useful "sideways" strength along the way. You should find sit ups / crunches a lot harder after doing these.

Hate to use him as an example, but the reason people like Zyzz looked shredded with obvious abs is primarily their diet. From memory, his was super strict and he didn't touch any fast food or anything sweet. I can't do this, I love food too much...thus I will never be as shredded lol...but I'm still trim because cardio can certainly make up for a poor diet. Not that mine's all that bad, but I don't knock back burgers and chocolate on the weekends.

Also, lol @ plank video...he's probably explaining some good things (I haven't watched the vid), but you'd think a still picture would suffice for planking instruction :P

Will do re pics.

I could do more cardio for sure, atm I walk the dog each morning which is only a small 20min circuit, which I jog most of (I find it hard to get going in the mornings) and then a bigger walk with the dog and missus a few nights a week. I could deffo be getting back into my bike or running though.

Same, no way I'll give up sweet things and tasty treats.

Ever tried running at night, before dinner? You should have more energy at this time from your food intake during the day. Though not the most motivating time, after a long day at work lol.

The morning walk is more so for the dog, as she's only 9mths and has lots of energy, I jog it just to get it over with faster.

At night, M/W/F I start exercising as soon as I get home, takes about an hour. On the off days Tuesday and Thursday, I'm likely to go for a bigger walk with Kate and the Dog and on the weekends we usually go somewhere with the dog and I do the usual BS of wash both cars, mow lawns (1280sqm block) etc so it's not like I'm inactive.

yeah GTST - thats my diet currently. No cereals tho.

meat + salad + balsamic vinegar = win. meat + broc/caul/carrot + S/P = win, too !

throw in tuna cans & pre/post protein shakes, plus a fruit smoothie a few times a week & thats it for me.

Might have a 6" sub 1x a week at Uni if required, see how I go. But real keen to cut out carbs (besides some Dextrose in the shakes).

Just got to make sure I have enough energy for workouts + study, so I'll balance it over the next month or so.

Today I got into the freeweight leg press and did some sets. Only 30kg lol (nothing on the guys who smash out +400kg at my gym), but that was VERY hard getting it up of the safety bars 1) due to the angles with my very long legs, its hard to fit in the machine, and 2) no knees really hampers how much you can initially push off with. think of it as doing a cable lat pulldown without the pulley for the cable to go over..... :/

- I do a bit of ab work in my routine, 3 sets of 50 crunches and 3 sets of 70 reps of an air bike/leg scissor type thing. So I have OK looking abs so long as I tense them and hold them in place. If I fully relax, I look 2mths pregnant and my stomach bulges out a small amount. Is this a sign of poor internal ab strength or weak core or is it just that every photo you ever see of someone posing they are flexing their stomach? My partners stomach does not do this and she doesn't have my ab definition or strength and doesn't do any special ab work (she's a runner). I sit all day so that might be it, relaxed abs all day though she does too? I don't think my body fat % is high as I've always been a leaner guy (I'm only 81kg at 6ft). She did say that from an early age she always held her abs in place and has good posture.

Thoughts?

You're fat!

Seriously. You can get awesome abs by never lifting a weight if your body fat % is low enough.

Eh, I didn't see the million posts since the one I quoted till I posted just now. Odd.

Edited by KezR33

You're fat!

Seriously. You can get awesome abs by never lifting a weight if your body fat % is low enough.

Eh, I didn't see the million posts since the one I quoted till I posted just now. Odd.

It took you 6 hours to type this reply? :P

you need to train your abs like any other muscle... no need to do sets with 50 reps... get some resistance whether it be dumbbells, medicine ball, cables or whatever and keep reps in the 8 - 15 range

your abs might stick out because you have too much anterior pelvic tilt... that is your lower back is excessively arched and your pelvis is tilted forward... this can be due to multiple reasons, do a search for some articles

I was reading a great one the other day but can't find it now... one comment that stood out was that excessive anterior pelvic tilt can make lean guys look fat due to the protruding belly

This one is okay

http://www.t-nation.com/free_online_article/most_recent/break_up_those_hips_and_fix_that_squat

This vid explains how to diagnose yourself

Nick I thought that adding weight and doing lower reps would make the muscle bigger, I don't to exacerbate the protruding look issue. Was under the impression that for abs reps were OK as tone is more the goal (in my case).

Also interesting vid.

You will all see what I mean when I post some pics, prolly Wednesday Night/Thursday morning, the most likely culprit is I'm just holding too much fat in the mid section due to my dietary choices.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...