Jump to content
SAU Community

Recommended Posts

Ok lets set this straight here instead of it being ridiculously all over the place.

REST TIMES DEPEND ON THE TYPE OF TRAINING YOU ARE DOING.

No 'ifs' 'buts' or 'maybes'

If you're resting more than 30 seconds in an endurance rep range work harder. If you're resting more than 90 seconds for hypertrophy work harder. If you can push out heavy strength-based sets one after another in less than 2-3 minutes, YOU'RE DOING IT WRONG

Is it possible to get stress fractures in your forearms from bench pressing? (I know this sounds retarded, but my forearms have been aching chronically for weeks now :S, and the only thing that's changed is I've been getting stronger and shifting more weight then I ever have before...)

Edited by GHOSTrun

Yeah, hate to admit it, but when I was reading a Zyzz interview he said he didn't do any oblique work because he was concerned it would make his mid section too big. Anyone shine some more light on it?

I always thought obliques just followed your body lines and being core muscles like abs, you're somewhat restricted on how they can affect the overall shape of your body. Maybe if you really built them up or you were shredded as fark they would affect it more.

Mine aren't far off the rib cage (see below; pic taken prior to my recent cut), so I don't think they play with my shape much. Even then, I'm stick thin in the waist and I've done too much lat work not to look like a pizza slice lol.

cZCn_6j3_original.png

Is it possible to get stress fractures in your forearms from bench pressing? (I know this sounds retarded, but my forearms have been aching chronically for weeks now :S, and the only thing that's changed is I've been getting stronger and shifting more weight then I ever have before...)

Where in the forearm does it hurt? Muscle or joint or bone? Is it getting worse?

Is it possible to get stress fractures in your forearms from bench pressing? (I know this sounds retarded, but my forearms have been aching chronically for weeks now :S, and the only thing that's changed is I've been getting stronger and shifting more weight then I ever have before...)

generally your bones should increase with strength and density as you start lifting more. Someone correct me if im wrong but everytime you lift heavy small stress fractures develope, they then heal and become stronger.. we just dont feel fractures most of time

Do you do much isometrics?

whats your Calcium intake like and where do source do you get it from?

If you make a fist and look at your knuckles, from the wrist to halfway up forearm is where the pain is and slight swelling, bit sore to touch, no discolouration. Between this pain in both forearms and even worse chronic pain in my left elbow and shoulder, makes benching a nightmare for me. Might have to give it a rest and switch to military press for a while because the weight would be half of what I'm doing on bench and considerably less stress.

I'd say I don't get as much calcium as I used to because my consumption of milk has dropped a lot in the last few years, but my bone density has always been good in dexa scans so don't think that's an issue?

Edited by GHOSTrun

There are major tendons that run all the way from your fingers to the forearm muscle, is it possible you're mistaking these for bones? I'd put it down to technique, there's nothing else short of a seperate medical issue that should cause that. Have you tried different ways of holding the bar? Specifically, the angle of your hands...e.g. knuckles pointing at the ceiling, knuckles pointing behind you. The angle of your hand can make a big difference to stress on joints.

The fact you can lift heavy without issue on deads and squats suggests to me it's a technique issue, as your "bones" seem fine on those exercises no? May need to just rest it or cut back the weight and let your body catch up to it.

I know tendons and cartilage develop microtears and heal back stronger/bigger, I suppose it makes sense that bones do too Joey.

I have the same forearm pain from time to time, and it is definitely bone related.

Yes you do develop small fractures in the bone after heavy resistance workouts because in order for your bones to strengthen in density (so that they aren't crushed under heavy load) they must break down and rebuild just like muscle tissue. Basically you have osteoclasts which break down the bone, and then osteoblasts which are bone forming cells. This process of remodelling constantly occurs if you continue to participate in regular workouts, and this is all part of:

Wolff's Law

"...states that bone in a healthy person or animal will adapt to the loads it is placed under. If loading on a particular bone increases, the bone will remodel itself over time to become stronger to resist that sort of loading. The internal architecture of the trabeculae undergoes adaptive changes, followed by secondary changes to the external cortical portion of the bone, perhaps becoming thicker as a result. The converse is true as well: if the loading on a bone decreases, the bone will become weaker due to turnover, it is less metabolically costly to maintain and there is no stimulus for continued remodelling that is required to maintain bone mass."

In my opinion, I'd say that because during a bench press movement where your arms are directly under the path of gravity, it's more trauma on the bones in your arm (radius, ulna especially) when you really go heavy. A good way to see this for yourself is if you pick up two heavy dumbbells and lie on the floor with your arms flat out at 90 degrees. It's pretty painful and it feels as if all the weight is pressing down on your bones alone.

In response to Birds,

Your obliques and abs will grow in size as do any muscle, so yes, the more oblique work you do with added weight means it will take away from your V-taper slightly as your obliques tend to bulge and grow outwards like your lats.

If you choose to work them heaps, you just need to shed a lot more body fat to retain your V because that area is also quite a large fat deposit for the body (think "love handles")

If you make a fist and look at your knuckles, from the wrist to halfway up forearm is where the pain is and slight swelling, bit sore to touch, no discolouration. Between this pain in both forearms and even worse chronic pain in my left elbow and shoulder, makes benching a nightmare for me. Might have to give it a rest and switch to military press for a while because the weight would be half of what I'm doing on bench and considerably less stress.

you need to see a physio or equivalent... I have a bad left elbow that causes me trouble when I curl, row or pull up with palm supinated... I can train around it but your issues sound more serious than that... get it checked

Birds, keep training those obliques! the thought that someone would deliberately avoid strengthening a muscle so they appeared larger/stronger is just a tad retarded... I have huge respect for BBers and what they do but sometimes............ face palm

Edited by NickR33

Ghosty.

But use a broom stick.

It's the best thing for shoulders, chest, elbows, wrists.

Trust me I'm 35 and falling apart and this keeps me together a little longer.

I start right out the edges, and do 3 reps, then move in a little from both side and repeat till my traps are burning.

Do it every time you walk past the broom stick.

or at least before and after any training.

and during if you can between sets.

Ghosty.

But use a broom stick.

It's the best thing for shoulders, chest, elbows, wrists.

Trust me I'm 35 and falling apart and this keeps me together a little longer.

I start right out the edges, and do 3 reps, then move in a little from both side and repeat till my traps are burning.

Do it every time you walk past the broom stick.

or at least before and after any training.

and during if you can between sets.

Fark. This is exactly what I need to be doing. My shoulder flexibility is crap and seriously hinders not only my shoulder pressing movements but also benching, not to mention posture. Gonna go grab a broomstick from the shed this arvo.

I also read an article on TNation that lists Cuban Curls as a good way to strengthen the shoulder, which should lead to increased strength in pressing.

Like this, except the "upright row" part of the movement is 'optional'

have heard that working the obliques and deadlifts thicken the waist area which in turn makes the 'V' harder to get.

guess you have to decide what look you're after and go from there.

Also Birds out of interest can you post your routine (if you havent already)?

Also, reps range that you go for, rest between sets, rep times ie 3-1-3?

Edited by -FIGJAM-

Ghosty.

But use a broom stick.

It's the best thing for shoulders, chest, elbows, wrists.

Trust me I'm 35 and falling apart and this keeps me together a little longer.

I start right out the edges, and do 3 reps, then move in a little from both side and repeat till my traps are burning.

Do it every time you walk past the broom stick.

or at least before and after any training.

and during if you can between sets.

i will add that to my morning stretches. :cheers:

Birds, keep training those obliques! the thought that someone would deliberately avoid strengthening a muscle so they appeared larger/stronger is just a tad retarded... I have huge respect for BBers and what they do but sometimes............ face palm

Yer only thing that's gonna make me give up woodchops is injury. As you know I'm going for looks over strength but I could never avoid training a useful muscle to make another part of me look big, that's just douchebaggery of the highest order. And now that I have visible obliques, I think the mid section would look plain without them anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I did end up getting it sorted, as GTSBoy said, there was a corroded connection and wire that needed to be replaced. I ended up taking out the light assembly, giving everything a good clean and re-soldered the old joints, and it came out good.
    • Wow, thanks for your help guys 🙏. I really appreciate it. Thanks @Rezz, if i fail finding any new or used, full or partial set of original Stage carpets i will come back to you for sure 😉 Explenation is right there, i just missed it 🤦‍♂️. Thanks for pointing out. @soviet_merlin in the meantime, I received a reply from nengun, and i quote: "Thanks for your message and interest in Nengun. KG4900 is for the full set of floor mats, while KG4911 is only the Driver's Floor Mat. FR, RH means Front Right Hand Side. All the Full Set options are now discontinued. However, the Driver's Floor Mat options are still available according to the latest information available to us. We do not know what the differences would be, but if you only want the one mat, we can certainly see what we can find out for you". Interesting. It seems they still have some "new old stock" that Duncan mentioned 🤔. I wonder if they can provide any photos......And i also just realized that amayama have G4900 sets. I'm tempted too. 
    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
×
×
  • Create New...