Jump to content
SAU Community

Recommended Posts

Another reason they can blink fast is iff you replace your blinkers with smaller ones like i did it lowers the resistance and the flasher unit thinks there is a blown globe you either need a different flasher unit or wire in some larger globes like i did

I'm not sure if this is relevant but when I disconnected the front indicator/foggy connector

and turned the indicator on, though there's no light but the interior dash indicator indicator flashes like crazy

I'm not sure if this is relevant but when I disconnected the front indicator/foggy connector

and turned the indicator on, though there's no light but the interior dash indicator indicator flashes like crazy

i think its the same situation where if a globe is broken you have broken the curcuit so if a globe is removed the curcuit is broken too? not 100% if that correct though..

^ yep, broken curcuit will make it flash faster too. i recently had this happen after putting my front bar back on. i thought it was a blown globe, but actually it was making poor contact in the holder. cleaned it up, problem solved.

If you havent changed anything then its going to be a blown globe.

i know it started with mine because i put smaller indicators into my front bar as i hated the big ugly orange ones.

i dont mind them flashing fast but does anyone know if its illegal?

If you havent changed anything then its going to be a blown globe.

i know it started with mine because i put smaller indicators into my front bar as i hated the big ugly orange ones.

i dont mind them flashing fast but does anyone know if its illegal?

Could cause people to have seizures(sp?). So would say that it's illegal.

there is a legal rate that all cars in australia must flash between, cant remember what it is off the top of my head, fairly decent size range though, also on my 32 i noticed it doing this, stupid thing has 2 blinker globes in the corner lights, took me a while to relalise

I've got this problem of having them go fast one day and normal the next. I think there's something loose.

I get this on mine from time to time. Turns out there's a water leak letting drops of water into the socket for the rear lights and causing a short. Once it dries out, it all works fine. When the rain stops after a wet period, I usually spray some electronic cleaner in there which evaporates the water real fast...

Might be something else on yours though.

Ok yesterday I took out the Amber lens after heating it in the oven,

put in some orange bulbs and glad wrap over the indicators (just a temporary solution)

connected it back up and today my indicators go like crazy, everything is working

but the indicators are flashing like 3 times a second.

It goes back to normal when I put the emergency lights on.

Any ideas guys?

Edited by POLICE
I get this on mine from time to time. Turns out there's a water leak letting drops of water into the socket for the rear lights and causing a short. Once it dries out, it all works fine. When the rain stops after a wet period, I usually spray some electronic cleaner in there which evaporates the water real fast...

Might be something else on yours though.

Hrmm, cheers for that mate. I'm gonna keep an eye out what happens after a down pour.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...