Jump to content
SAU Community

Recommended Posts

hey guys!

Yea i finally got my hands on my very first skyline! I was looking for series 2 at the beginning but ended up buying series 1.

So far I'm loving it, makes a great noise and goes reasonable enough for now. It's not as much modified as some other skylines around but does the job for now.

Full 3" Jasma exhaust

Hybrid frount mount

HKS pod

Turbosmart dual stage boost controller

JE Design 3 piece wheels 18x10 at the back :P

Upgraded struts and lowered

A really dark TINT!

Also just bought GTR style grill and will be looking into series 2 front bar

WE2533126946.jpg

WE2533126946_A.jpg

WE2533126946_B.jpg

WE2533126946_C.jpg

WE2533126946_D.jpg

Let me know what you guys think, or wave when you see me around the city :D

Also whats the legal height for an R33 ??

cheers

vlad

Edited by dovla
Link to comment
https://www.sau.com.au/forums/topic/201353-finally-got-it/
Share on other sites

nice car bro congrats

only thing I don't like is the front bar :P

would look much better with a modified 95 m-spec front bar :D

ohh and lowest legal ride height in NSW is 100mm ground clearance at the lowest point on the car ...

so if your exhaust is the lowest point on your car it has to be at least 100mm of the ground to be legal :P

it seems to be sitting at a nice height now I wouldn't go to much lower than what it is now

hope this helps

welcome to the skyline fraternity !!! :D

Link to comment
https://www.sau.com.au/forums/topic/201353-finally-got-it/#findComment-3579203
Share on other sites

Min legal eyebrow height for R32 and R33 turbo models is 360 mm from centre of wheel to guard (in SA).

Almost every skyline on the road would be too low - that is really quite high.

Looking at yours I'd say it would be under that.

Link to comment
https://www.sau.com.au/forums/topic/201353-finally-got-it/#findComment-3580002
Share on other sites

congrats on the buy mate....car looks in good condition....but if you were going to get a different front bar i would just go for an aftermarket kit....as changing you lights, hood and the lot will be expensive and you will look like a SII tryhard....just go with an aftermarket kit all around....it will look a lot better with SI lights and all....

Link to comment
https://www.sau.com.au/forums/topic/201353-finally-got-it/#findComment-3580116
Share on other sites

Min legal eyebrow height for R32 and R33 turbo models is 360 mm from centre of wheel to guard (in SA).

Almost every skyline on the road would be too low - that is really quite high.

Looking at yours I'd say it would be under that.

Hey chops......I got my R34 GTR through inspection last week and spoke to Paul from Vehicle Standards at Regency 1300 882 248 first to find out the minimum heights.

He said that the R34 Turbos were 340 Front & 345 Rear.......Non turbos might be different.

Rang him again 10 minutes ago and asked him about R32 & R33.......he said 345 Front & 355 Rear.......again, Non turbos might be different because he couldn't find a listing for GTR's but wanted to know if it was Turbo or not.

So now it begs the question, are ride heights for single turbos different to twin turbos?.....who knows how these guys operate.......probably varies with each inspector and how he translates the rules.

Link to comment
https://www.sau.com.au/forums/topic/201353-finally-got-it/#findComment-3581029
Share on other sites

Thanks again for the replies :D

I don't mind the front bar too much but just makes the car look a bit dull!

Also just bought the gtr style grill so hopefully that will make slight difference :)

No mods will be done at this stage, as the car goes enough as it is (on high boost tho! )

cheers

vlad

Link to comment
https://www.sau.com.au/forums/topic/201353-finally-got-it/#findComment-3581842
Share on other sites

Hey chops......I got my R34 GTR through inspection last week and spoke to Paul from Vehicle Standards at Regency 1300 882 248 first to find out the minimum heights.

He said that the R34 Turbos were 340 Front & 345 Rear.......Non turbos might be different.

Rang him again 10 minutes ago and asked him about R32 & R33.......he said 345 Front & 355 Rear.......again, Non turbos might be different because he couldn't find a listing for GTR's but wanted to know if it was Turbo or not.

So now it begs the question, are ride heights for single turbos different to twin turbos?.....who knows how these guys operate.......probably varies with each inspector and how he translates the rules.

My info is from the 11/2004 version of the document - there may be a more current version but I can't find one.

The info you got agrees with the info in the document for R34 GTRs, and the info he gave you on R32s and R33s seems to be for non turbo models.

I've attached a copy here for all to see.

post-6487-1200355939_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/201353-finally-got-it/#findComment-3582302
Share on other sites

Thanks again for the replies :D

I don't mind the front bar too much but just makes the car look a bit dull!

Also just bought the gtr style grill so hopefully that will make slight difference ;)

No mods will be done at this stage, as the car goes enough as it is (on high boost tho! )

cheers

vlad

wats it running on high boost....as in how many psi's and wat power is it making...just keen as i got a S1 as well....

Link to comment
https://www.sau.com.au/forums/topic/201353-finally-got-it/#findComment-3582341
Share on other sites

mate i duno if you still have those number plates on your car but if you do you have just listed the state your in and the mods on your car wiv the number plates theives/regency love this stuff mite pay to blur them out in photo shop or something nice looking clean car though congrats on the purchase

Link to comment
https://www.sau.com.au/forums/topic/201353-finally-got-it/#findComment-3582626
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is it alright to top up with just another green coolant?
    • thanks GTSboy. My confusion at the moment is i am trying to locate the ignition, ECU battery power and the ECU negative The closest thing i can find is the for the S15 on Page 8 of the Wiring Specialties web page https://drive.google.com/file/d/0B9F33_M_GgENQnZ6STMxVmVNd1E/view?resourcekey=0-eZ4nNRwRoqa1qvKlWWHm8A I cannot find the same diagram for the R33 RB25DET Series 2 dash plug pin out.... Do you know what the Pins? or know where i can find the same pinout diagram for the RB dash plug? Thanks for the advice on the box... i like a 6 speed so might be on the lookout or the box now.. a topic of discussion for another post...
    • Will have a look at that. I cant see any leaks 
    • Put another overflow bottle (ie, a 1.25 coke bottle or similar) under the overflow hose and see if it is being pushed out there or if it is disappearing into the engine.
    • Staring on a stand is no issue. You just have to wire everything up, give it fuel and cross your fingers that the stand is robust enough. Arranging the inlet plumbing is often the hardest part, without any surrounding structure to hand some of it from. No need for coolant if you only want to run it for <1 minute. As to the gearbox - I think the little Aisin box is a bit stronger than the other small Nissan boxes that went behind SRs, but I wouldn't be too keen to test its limits with the torque of a boosted 25. I don't know if you can retain the box and the tailshaft. The box won't connect to the RB without an adapter of some sort, which is either a plate that will push the engine forward (which is not good for fitting it into the bay's available space) or push the box back, which messes with the box position and tailshaft length - OR - cut and shut work on the bellhousing, which is a long way from "least modification". I'd be buying a new 370Z 6 speed or similar, doing what has to be done to that to make it fit RB (ie, cut and shut bellhousing) and the requisite tailshaft custom/mods.
×
×
  • Create New...