Jump to content
SAU Community

Recommended Posts

I have a reasonable budget to work with (cash & a 6k credit card I haven't really used, and would prefer not to), but I'm a bit undecided at the moment on what to actually do. For the last 5 months I've had a bodykit sitting at home doing nothing because about a week after I got it, I got a yellow sticker I've only just managed to get off. Otherwise about 4 months ago I would have already had this on...

Work to the car to get it cleared is a touch on the expensive side (lets just say the 2 following options would have been done by now, but realistically all I can do is 1 for now), but I'm looking for other opinions on what you might do in the same situation.

a) I have a bomex front bar & side skirts, as well as some gtr rear pods that would cost about $1300 roughly to fit & paint. That would take my car from looking plain (sleeper if it wasn't for the front bar stickers) to a more "respectable" look. My current, shit, series 1 bumper has a lot of stone chips & is very scraped on the bottom of the bumper (bad experience with a driveway/mountain in Qld), and really detracts from what's behind it. Got no side skirts on the car or anything either.

b) I am running a very decent amount of power with stock injectors & cams, so if I replaced those with some aftermarket gear I'd be looking at more power, but also won't be stretching the limits of the car. With this I would probably be looking at some splitfires as well which would add to the cost, prob about 2k for all of it to be done.

c) Maybe don't spend it on the car, but if I don't, what? Buying a house just won't be happening at the moment (but regardless of what I do, my promotion I'm looking at in the next 6 months or so would mean I would then be able to look at doing that with another person or two) Don't really have much apart from the car so ideas are limited!

That is all :(

Link to comment
https://www.sau.com.au/forums/topic/204089-tell-me-what-i-should-do-next/
Share on other sites

Well if you`re happy with the power you got at the moment then i would either use the kit you have or sell it since its only sitting there gathering dust.

Not sure on what you got in comfort wise as in the seats, perhaps look at a seat upgrade and maybe some upgrade to the rear seats.

Or even a suspension upgrade if you haven`t already done so.

Stock car look can be less attraction to the police at times and also fun when that V8 rocks up beside you wanting to give you a run and you leave him with that stunned look on his face eating your dust.

Anyway just my 2 cents worth.

Good luck on what ever you decide on.

Edited by Woodys


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...