Jump to content
SAU Community

Recommended Posts

Hey all,

Went to calder last friday for the 1st time and and ran my car a few times, was wondering what sort of times other similiar cars was getting as i was going up against 11 sec cars!

My car and Mods:

1993 R33 Gts-t (Auto)

Performance mods:

Apexi N1 catback Exhuast

R34 Side mount cooler

running 9 Psi

Tyres: 17 inch rims with 245 continental tyres (about 60% thread) 22 PSI

and everything else is pretty much stock. Not tuned or anything like that.

My best time was:

14.29 @ 157 km/h

most my times was between 14.3 and 14.6 - i had about 11 runs.

I found that the car would launch hard but then die in the last 100 meters :D

i would be very happy with that time.

our skylines up north just cant seem to push the same times. different track and maybe the prep will probably be part of the reason.

what 60ft time?

hmmm really? the weather could also play a part i guess....on friday (when i went) it wasnt too bad, track temp was about 24 degrees..

60ft time was: 2.11

660' - 9.12 @ 125 km/h

That's a good time.

Are you planning to go quicker?

ye id love to break into the 13 seconds... and then i will be happy.

My car is a daily driver, ive had it for about 5 years and i've done 110,000 km's on it since ive got it...

I rekon maybe with a FMIC, high flow cat + dump pipe i could improve the top end a bit and maybe break into the high 13's!

But at the same time, as it is now, its great for day to day street driving / over taking and quicker off the line than more modified / tuned manual R33's of some of my mates and i don't know if i want to lose that to gain a few milliseconds on the drag strip!

What was your 60ft times?

Their is some easy time to be made up at a reasonable cost.

1) Get yourself a pair of R32 GTR rims (or 300ZX rims) and buy a new pair of Mickey Thompson ET Street tyres. This will lower your 60ft time without a doubt and should cost under $700.

2) Get a 1 piece front/dump pipe along with a new hiflow cat to finish off your exhaust system. You will have more power right through the rev range which will result in a higher terminal speed (currently ~94mph) and should cost under $700 as well.

What was your 60ft times?

Their is some easy time to be made up at a reasonable cost.

1) Get yourself a pair of R32 GTR rims (or 300ZX rims) and buy a new pair of Mickey Thompson ET Street tyres. This will lower your 60ft time without a doubt and should cost under $700.

2) Get a 1 piece front/dump pipe along with a new hiflow cat to finish off your exhaust system. You will have more power right through the rev range which will result in a higher terminal speed (currently ~94mph) and should cost under $700 as well.

60ft time was 2.11

thanks for the tip! ye i'm def going to invest in making the exhaust to turbo back me thinks!

Justjap have a nice deal going for you:

http://www.skylinesaustralia.com/forums/JJ...RB-t204414.html

So much cheaper than I first thought, wouldn't take more than an hours labour if it is a straight fit to your existing cat-back exhaust so you should be able to have it fitted for about $500 all up.

is it losing traction on launch?

being auto and stockish, I don't think it would.

anyway.

to get something like a 13.9 (in to the 13's as you're said).. get the exhaust finished (dump pipe and front pipe in one and a new large cat).

then get an SAFC and have it tuned.

Even the blue screen SAFC would get you a good increase in power, especially in the upper end.

the Blue screen ones would be below $300 now for sure.

dump/front pipe in one can be picked up for about $200 from a number of places brand new.

SAFC tune will probably set you back about $200.

all of that easily under $1K.

should push power to near 190rwkw.

should net you 13.xx

if you are losing traction on launch, then look in to tyres too.

I would also race with 16's instead of 17's.

I dare say that your 17's with tyres would weigh more than the stockers which weigh 16kg with tyres.

EDIT - don't replace the R34 SMIC with a FMIC.

you will lose the response that you love at the moment.

it is more than up to the task.

If the R34 SMIC doesn't have any ducting to it, I would look in to making one for it.

Water spray is another option but probably not needed.

Edited by GTST
What was your 60ft times?

Their is some easy time to be made up at a reasonable cost.

1) Get yourself a pair of R32 GTR rims (or 300ZX rims) and buy a new pair of Mickey Thompson ET Street tyres. This will lower your 60ft time without a doubt and should cost under $700.

2) Get a 1 piece front/dump pipe along with a new hiflow cat to finish off your exhaust system. You will have more power right through the rev range which will result in a higher terminal speed (currently ~94mph) and should cost under $700 as well.

his current mph is more like 97

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...