Jump to content
SAU Community

Funeral

bucket

By bucket,
in General Automotive Discussion

 Share

Recommended Posts

PranK Grand Master

PranK

Posted
Posted
Originally posted by Initiate

Agree on the waste of a nice car, but shouldn't the emphasis here be on the poor sod who probably isn't alive anymore, or at the very least very seriously injured???

Amen brother!

screw the car, i feel sorry for the ocupants.

Link to comment
https://www.sau.com.au/forums/topic/2054-funeral/#findComment-38065
Share on other sites
Neil Grand Master

Neil

Posted
Posted
Originally posted by carlo

Thats what happens when you lose control of your car. If your not in control then your not going to have much luck.

The 2nd photo is a good example why we have to have intrusion bars on our imports. Why they dont have them in japan is beyond me.

R33's and R34's have intrusion bars as standard.

It's a cold hard fact,,,if you race hard on the street that sort of crash is always a possabilty....The 1st cars not that bad,,,,the rear end has absorbed most of the impact,,,the o/s/r 1/4 has done its job very well. As for the 2nd pic ,,,well hope no-one was in the passenger seat,,,,. I see this crap on a regular basis,,,,We actually drive a VERY safe cars......Sick person I am,,,,,can I have the Wheels off the 2nd car,,,they look okay.

Neil.

Link to comment
https://www.sau.com.au/forums/topic/2054-funeral/#findComment-38883
Share on other sites
Laurence Mentor

Laurence

Posted
Posted

Side intrusion bars would (and did) do sweet FA on the car that poled the passenger door!

Just thought I would make mention of the two pictures I contributed to wreckedexotics.com :)

http://www.wreckedexotics.com/cars3/new/35..._071902_04.html

http://www.wreckedexotics.com/cars3/new/35..._071902_03.html

Link to comment
https://www.sau.com.au/forums/topic/2054-funeral/#findComment-38954
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...