Jump to content
SAU Community

Recommended Posts

It should be heaps richer.. I pull 500km from a tank .. 400 from half a tank (I dont know how that works, but it does)

I dont know maybe your ecu is remapped or somthing but if you remember mine id get about 300km or less a tank and when I added the FMIC it was like 150km a tank.. shocking stuff..

I need a fuel pump I think, and want to have injectors in sometime around then, then im finally going power FC i think.. who cares ill just spend the big $$$

  • Replies 200
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

R33 powwwah!

Good to see the threads alive again :sweat:

My car has the flu so will rock up with stock exhaust :teehee: Stop laughing.

Don't worry, i'll be the granny for this one but soon enough you'll fear R338OY!

See you blokes there, i'll be at the Dyno day too.

How about we go halvsies on my:

HKS pump

Nismo Injectors

Highflow turbo

Power FC

Ill go halves with your pump if you back my mods :) FAIR DEAL!

I'll even pay for my tune!

You drive a hard bargain Nat...

Maybe we'll just stick with the walkie talkies and 200rwkw :banana:

Edited by R338OY

ofcourse Anna34 .bring your friends along coz it gets boring if you're driving alone which happens to me and R33BOY all the time..this should be a really gud turnout..so many 34s, 350z, v35, r33, r32, 200sx all we missing is r31 and old school skylines and new r35gtr

oh YAY! =)

Thats awesome! How come you guys like to travel alone? It gets so lonely!

BLOW UP DOLL and CHOCOLATES AYE??! lol i think i'll bring a camera!

Thanks guys! wooo! :D:(

No one bitching in your ear + good music = relaxing :)

I'll try and be there despite work, hope the weather is good and look forward to meeting you guys




  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...