Jump to content
SAU Community

Recommended Posts

spotted a white r34 "RPM034" on south rd this arvo, followed not long after by a silver r34 4 door, normal state plates....

a white r33 at salisbury in the fasta pasta car park

a black r33 gtr on montegute rd or whatever it is called this afternoon

-White R33 on Currie Street at 11.30pm

-Black R34 on Grote Treet at 11.50pm

-Unknown colour R33 on Marion Road at around midnight (my bus kept up with it for about 8 stops, even though it had to stop at almost all of them :) )

Spotted silver 33 gtst trying to race a biker up Torrens Road!

When when the car drivers learn ... :P

hha true. Ive seen a few cars beat the bikes tho. not often.

I remember a V8 valiant killing a bunch of bikes once . very good to watch.

A few gtrs would give a bike a good run.

spotted a black 34. going down nnrth east road . friday. around 330pm. looked nice

hha true. Ive seen a few cars beat the bikes tho. not often.

I remember a V8 valiant killing a bunch of bikes once . very good to watch.

A few gtrs would give a bike a good run.

spotted a black 34. going down nnrth east road . friday. around 330pm. looked nice

The only reason a car would be in front, is thats because that where the biker wants them.

Just because you're in front, doesn't mean you won! :P

Don't be fooled thinking you can beat a serious sportsbike rider ... unless you and your car can do under 10sec 1/4 mile times. :down:

Drag racing scooters or 250ccs doesn't count :(

Edited by RubyRS4

Oh, what I was going to say was ...

Spotted a silver S2 Stag at Dazzlers on Port Road about 10.30pm last night. Went to wave, but driver busy cleaning cabin.

This morning, spotted a white S2 Stag at the Regnecy Park car park near the play equipment.

Saw some 70 year old grandpa at work with a white R33... thought that was quite humerous.

Also saw an R33 and R31 racing from the turn of the lights at the South Road/Anzac Highway Intersection.

The only reason a car would be in front, is thats because that where the biker wants them.

Just because you're in front, doesn't mean you won! :D

Don't be fooled thinking you can beat a serious sportsbike rider ... unless you and your car can do under 10sec 1/4 mile times. :devil:

Drag racing scooters or 250ccs doesn't count :(

yeah a serious bikes a bit diff but 250s ive seen go down. im also guessing the intial snap off the line big part of how bikes are faster so a rolling start against a 250 a good car could win. also if the rider aint that good or a bit chubby could also effect it :D

The only reason a car would be in front, is thats because that where the biker wants them.

Just because you're in front, doesn't mean you won! :)

Don't be fooled thinking you can beat a serious sportsbike rider ... unless you and your car can do under 10sec 1/4 mile times. :(

Drag racing scooters or 250ccs doesn't count :)

I thought this was an SAU Spotted thread?

Save the bike talk for the wasteland, or go to temporary_australian.com.au

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...