Jump to content
SAU Community

Recommended Posts

I receive my engine for my S13!! The target I said again is 10.5sec at quarter mile so 350-440 wkw

Without to know before buy it the engine have

HKS Pistons 87mm

HKS Rods

HKS 272 rods

HKS adjustable gears (very old series without degrees print)

Nismo oil pump

But!! R32 early crank and they didn't put jun crank collar... absolutely no wear at oil pump but I need to put jun crank collar?

Also it has stock headgasket and stock studs... and we find a little water at 3rd cyllinder... the gasket was blown so we break down everything!

So I need to buy a gasket and a arp stud kit... I will do also the "oil problems job".. external oil return and tomei oil gallery offrice!

What thickness do you suggest me?

It has acl bearing but we saw one rod bearing a little worn so we will replace with acl again the rod bearings!

Also I will put an aftermarket timing belt because it has stock!

It has Greddy 8 iridium spark plugs!

272 cams aren't toooo big???? :| :| :|

What rev limit I need with theese monster cams?? :| :| :|

What rpm can I run without harmonic ballancer?

Also at the parts I received they don't send me the dropping resisostor for injectors!!

So either I buy one or i will use high impedence injectors?

Link to comment
https://www.sau.com.au/forums/topic/206069-my-project-problems/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sorry, are coilovers ACTUALLY ILLEGAL in NSW? They aren't in Vic, as long as they retain 70% of stock travel and the car is above 100mm off the ground. Does NSW actually have a law making coilovers actually illegal? RWC/Blue Slip/Engineering people not knowing the actual f**king laws boils my blood. Demand them to point to the documentation that states a coilover is illegal. (it may exist in NSW )
    • But seriously, can we ask for the results of the "tip a bottle of metho into a nearly empty tank" experiment?
    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
×
×
  • Create New...