Jump to content
SAU Community

Recommended Posts

  • Replies 118
  • Created
  • Last Reply

Top Posters In This Topic

thats bullshit, you cant accidentally shove a spark plug as a sump plug no matter how stupid you are. glad it didnt hit something and come out. if you spill pm me the workshop name as im about to get some work done to my car

thats bullshit, you cant accidentally shove a spark plug as a sump plug no matter how stupid you are. glad it didnt hit something and come out. if you spill pm me the workshop name as im about to get some work done to my car

Thats a very good point...! What if he wiped it out on a speed hump, dropped all his oil and then totally lunched the whole engine...?

Maybe they dropped the sump plug into the bucket. Decided to find something to plug the hole whilst taking the oil pan to find sum plug and the spark plug was the perfect fit.

Taken oil pan to drain to find the sump plug only to see it fall into massive drum of oil. Phone rings a few times, boss is screaming that he needs the host and how long does it take to change oil.

Employee decides to tighten spark plug (correct torque settings of course) and fill oil in attempt to discredit boss.

My theory anyway...

This is shit we have all forgoten things but to fit a spark plug as a sump plug. Even if you droped the plug in the drain tin just pick it up or place another tin under the drips and drain the oil from the tin with the plug in it. This (mechanic) needs to recheck the car and then tell his boss why its back and tell him whagt he did i dont think he will be there long if his nogt gone already. Happy hunting, let them have it i know i would.

Thanks heaps guys for the support :D god knows i need it, coz my little saga gets worse.....

here goes.......

along with fixing my idle problem i had a leaky sump bolt, so they thort they would fix it for me. They thort they would helicoil a new thread in using a particular thread pitch and size 14 by 1.25, this size ONLY, im mean only comes in spark plugs, no compamy makes a bolt in this size it has to be custom made.

so i have to retap it AGAIN to a lagrer size :ermm:

THE EXSUCE - the mechanic who works on my car asked one of coworkers to plug it with something thats fits, and then forgot about it. He says they took his words too literaly to plug it. He was there when the car went out but didnt check it.

all i have to say it PET/GTECH in cambellfeild suck dont go there, im sure there are lots of happy customers but im not one of them.

i dont want to have anything to do with them, no agro no yelling, id rather spend my time with people who give a sh#t about what they do and how they do it, there not worth my time and effort.

they have done some top work for me but this was just down right careless.

Edited by robbieraver
i dont want to have anything to do with them, no agro no yelling, id rather spend my time with people who give a sh#t about what they do and how they do it, there not worth my time and effort.

they have done some top work for me but this was just down right careless.

if your taking your car to around campbellfield area

take it to CREATD Motorsports

well trusted and recommened workshop

thats where i take mine and couldnt be happier :P

so id say your relationship with them has possibly lost its spark??

:ermm:

Troy your a pissa :D

if one of my guys even thought of doing that they better pack up their tools and walk before i get to them.

There is no excuse for that, absolutely none.

its people like this that drive the mechanical trade down the shitter and force the good guys to work for f**k all

my partner and i check every single car that leave and make sure everything is 110% no ifs, no buts.

f**k this kind of stuff shits me to no end

occupation health and safety! this is dangerous plug could have hit something come out... oil drained out... engine ceased caught on fire and u could get burnt or even killed!! the work shop should do as rudd did and say sorry! :P :P :):P:banana::banana:

glad nothing went wrong but its a head f**k do have i different sized sump plug!! sorry to hear mate and hopefully u get some top work done next time by ur new workshop!!

peace

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...