Jump to content
SAU Community

Brakepads For A Track Day / High Performance Driving Day

some_cs_student
 Share

Recommended Posts

SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

gareth, for the time being, i think i may have been discussing different pad compounds with people.

rang qfm direct and confirmed A1RM's are rated to 780 degree's, and Brake West confirms that but call them K750's because in their own testing, they feel that's a slightly more accurate measurement of their temp range. Said they're fine at 780 but they feel 750 is where they'll be 100%, 100% of the time :)

i've ordered some A1RM's from the group buy 'markk' setup

some_cs_student Veteran

some_cs_student

Posted
  • Author
Posted
gareth, for the time being, i think i may have been discussing different pad compounds with people.

rang qfm direct and confirmed A1RM's are rated to 780 degree's, and Brake West confirms that but call them K750's because in their own testing, they feel that's a slightly more accurate measurement of their temp range. Said they're fine at 780 but they feel 750 is where they'll be 100%, 100% of the time :down:

i've ordered some A1RM's from the group buy 'markk' setup

The group buy doesn't supply the pads for the brembo's on R33 GTR's :laugh:.

So I'll have to do with what I have for now, I'm out of money and its too late to get them before the track day, if I have to retire early I will retire early on the day and get pads waaaay before next track day :)

Regards,

Gareth

  • 4 weeks later...
Kinks Grand Master

Kinks

Posted
Posted
If you're running street tyres you should be able to get away with a decent set of street/track pads, IE DS2500 or those QFMs....

If you're using the pads in your daily street driving, don't even bother with DS2500s as they need heat to work properly so you'll have very ordinary brakes when cold. I was recommended against them in my daily.

I haven't had any fade problems with DS2000's (Formulas) and they work fine when cold. Stock power, stock rims etc so if you are modified you might run out of brakes a bit easier.

djr81 Grand Master

djr81

Posted
Posted
If you're using the pads in your daily street driving, don't even bother with DS2500s as they need heat to work properly so you'll have very ordinary brakes when cold. I was recommended against them in my daily.

I haven't had any fade problems with DS2000's (Formulas) and they work fine when cold. Stock power, stock rims etc so if you are modified you might run out of brakes a bit easier.

I use DS2500's and they work fine from cold. They are low dust and have a good friction coefficient. The only real downside is that the distributors know they are good & charge accordingly. Think $300 for a set of front pads for you R32 GT-R.

So they will make a perfectly good selection for a daily although you need to understand if you don't do any track work you are better off with a road style compound.

some_cs_student Veteran

some_cs_student

Posted
  • Author
Posted
I use DS2500's and they work fine from cold. They are low dust and have a good friction coefficient. The only real downside is that the distributors know they are good & charge accordingly. Think $300 for a set of front pads for you R32 GT-R.

$300/set? I could nearly afford 2 sets of QFM A1RM pads for that price ;)

I will buy QFM pads and see how they go.

gslrallysport Experienced

gslrallysport

Posted
Posted
$300/set? I could nearly afford 2 sets of QFM A1RM pads for that price :(

I will buy QFM pads and see how they go.

Yeah, $300 for a pad that's no better than QFM A1RM or EBC Red Stuff is a bit steep. But, they have the name and can get away with it. QFM A1RM for the win.

some_cs_student Veteran

some_cs_student

Posted
  • Author
Posted

Don't forget to feed back info into the sticky:

http://www.skylinesaustralia.com/forums/Br...0&start=120

About general brake pad info :P

Thanks for all the feedback, I will be getting some new brake pads but probably won't rate them yet as I don't have enough experience in my car to judge how good they are.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...