Jump to content
SAU Community

Recommended Posts

Hey guys,

Firstly, on behalf of SAUWA i would like to extend a big thanks to Abdus and the crew at Tenagah Motorsport. The crew have been working flat out all week until late hours (to get some of our members cars ready for today) and then to give up their Sunday to run this event for us is a fantastic effort! Also a big thanks to their families for letting them :D (you married guys know what im saying :() I am sure the winners have great appreciation for their prizes that were donated! A very big thankyou aswell for providing some food and drinks today...it was well needed! I hope all the Tenagah crew are at home now enjoying a nice cold beer! You deserve it! :)

Secondly, thank you all for coming along wheather to enter or just to spectate or stand around and have a chat! The numbers were well beyond my expectations. I hope you all enjoyed the day.

WINNERS CIRCLE:

Highest HP RB26.....Jonn @ 437.7

Highest HP RB25.....Ossie21 (Nathan) @ 344.4

Highest HP RB20.....NO ENTRANTS!!

Lowest HP..............Chuckie @ 140.8

RESULT:

GTS-t Vspec........525.1 (R33 GTS-T) (Excluded from winning....sorry :( )

Ossie21..............344.4 (R33 GTS-T)

Gav....................436.0 (R32 GTR)

Jonn...................437.7 (R32 GTR)

SkyRyan.............234.0 (R33 GTS-T)

InfamousT..........213.7 (R32 GTR)

Inthisglass..........148.5 (R33 GTS)

Chuckie..............140.8 (Stagea)

Lach32...............96.1 (S15)

GWP021.............193.3 (R33 GTS-T)

Yorik..................250.2 (R32 GTR)

Topaz.................297.1 (R32 GTR)

MrGazza.............146.6 (R33 GTS-T)

Gtstee................245.3 (R33 GTR)

Russell James.....333.7 (VN Calais)

Ahh33s2.............210.9 (R33 GTS-T)

Shenron.............206.4 (R33 GTS-T)

Rawzer..............241.3 (R33 GTR)

Pal.....................253.3 (R33 GTS-T)

Woodsy..............279.2 (R33 GTS-T)

Peter..................197.4 (R33 GTS-T)

Frank.................294.3 (R32 GTR)

Ant (Non Official entry) 440 (R32 GTR)

If there is any errors in there please let me know and i will correct them.

Congratulations to the 3 winners. There was no winner in the RB20 class as there were no entrants...i even tried to convince Abdus i had done an RB20 Conversion to my car :D

Again, thank you all for coming! Abdus has suggested maybe another Dyno Day Later in the year for those who did not have their car ready, or have some mod beings planned at the moment....seems like a fair idea to me and i think SAUWA will accept that offer :D

Cheers

Brad

SAUWA Motorsport Coordinator

Link to comment
https://www.sau.com.au/forums/topic/207528-sauwa-dyno-day-results/
Share on other sites

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

after the turnout today brad id say if abdus is willing to have us again another event later in the year would be great

and a massive thankyou to you the tenagah team and everyone else involved in making this happen

mabe next time paully will even remember the membership packs (and my damned shirt) lol

Abdus was very happy with everyone that was there today. He said we were a friendly bunch of guys and very easy to get along with :(

(mind you, there were a few guys who made their exit a bit of a scene....that could of been avoided :D )

i enjoyed the day, always good to see a big group of lines.

also nice to see that my car put out more HP than a turbo car (even if it leaned out and couldn't run)

thanks to everyone that made it possible!

ROFL........ expect mine didnt go over 3000rpm

CONGRATZ to you!?

new fuel reg this week, shall get dyno'd week after =)

The sunburn I copped was worth it for today, was a good day of course with a bunch of people like us :( Shame about the cars that were running lean, but think of it this way. That 50/60 bucks could be saving you a lot more in the future if you find the problem before it became a bigger problem :)

Running lean means that the engine is being starved of fuel. Usually means that it needs bigger injectors, or better fuel pump, fuel rail etc. Basically the amount of air being forced in is not being matched by the fuel system.

ROFL........ expect mine didnt go over 3000rpm

CONGRATZ to you!?

new fuel reg this week, shall get dyno'd week after =)

I doubt a fuel reg will fix this, I'd suggest it's more likely to be the fuel pump.

Thanks to Brad for organising this, the event ran really smoothly :(

Thanks to Tenegah, great venue, and very professionally run :)

Pity I missed out on a trophy :blink:

On behalf of Tenagah Motorsports I would like to extend a BIG thank you to Brad, the entrants and all the SAUWA crew that made it to the dyno day yesterday. It was fantastic. You're all a great bunch of guys and that made for an awsome day.To the class winners I hope to see you in the shop soon to spend the $$$$$$$$$.

I'm really looking forward to another dyno day later in the year, but I hope to plan other joint SAUWA/Tenagah days before then.

Thanks again

Abdus & Team

:(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...