Jump to content
SAU Community

Happy birthday - Andrew

Maxx

By Maxx,
in South Australia

 Share

Recommended Posts

Nightcrawler Grand Master

Nightcrawler

Posted
Posted

damn .... thanks guys for all your well wishes!!! Only just checked the forums now (since Thursday).

Man, what a night .... I think I said this a few weeks ago after the last party at my place, but fark me never again.

To say I'm under the weather is not at all fair to bad weather.

Had a top night out; the karts were awesome (even if I am a bit sore from some of Matty's crash efforts), the 8-ball was great, the big screen Gran Turismo 3 and Mortal Kombat a blast, and the girls at 108 sensational (for dirty ****s, that is) .... oh and a big THANK YOU for getting that chick at 108 to strip me down to my boxers and put me in a clam-shell bath with her naked on top - I am still smiling from ear to ear :) Karma at Le Rox was bloody awesome later too - even if I did leave after only an hour or so due to some fisty-cuffs :) .... I grabbed a souvlaki and a cab and fell into bed around 4:30am .... not bad since our first beers at the Gepps Cross hotel were at about 4pm ;)

Pawley Proficient

Pawley

Posted
Posted
Originally posted by Nightcrawler

even if I did leave after only an hour or so due to some fisty-cuffs :) .... I grabbed a souvlaki and a cab and fell into bed around 4:30am .... not bad since our first beers at the Gepps Cross hotel were at about 4pm :(

the grog and the titties i missed out on dont worry me that much.... but an all in with SAU members.... :fight!: i wished i hadda seen that!

Nightcrawler Grand Master

Nightcrawler

Posted
Posted

nah Pawley it wasn't as good as that - I left Digs and Matty to go for a slash and some yobbos were smashing each other in the toilets, I helped break them up and sort them out - then was ushered by a bouncer outside .... I went for a bit of a walk to get some air, next thing I knew I was in a taxi on my way home. Don't remember too much about it actually - the details are very fuzzy. I am still quite seedy today ;) .... poor old man that I am :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...