Jump to content
SAU Community

Recommended Posts

That's correct, most people are flat past the tower. The quick cars (aka Skylines/Supras/Porsches) are usually 180+ there, with a slight lift/brake tap for the kink approx 200 metres further on.......

Giant's 32 would be better than 400 klm/h there I'd say.

Edited by Marlin
  • Replies 101
  • Created
  • Last Reply

Top Posters In This Topic

400 ? typo ?????

and yea, im not gonna bother with lakeside till they have semi realistic noise restrictions =\ a stock HSV or anything with some grunts would prob be above 92 at the top of a gear going along that straight.

400 ? typo ?????

and yea, im not gonna bother with lakeside till they have semi realistic noise restrictions =\ a stock HSV or anything with some grunts would prob be above 92 at the top of a gear going along that straight.

400? No, of course I'm not serious, just a sarcastic quip mate.

That's fair enough, but I don't think a stock anything would get pinged. The only one pinged the other day was a racing 993 air-cooled Porsche with open pipes. Johnnyo's 300+ rwkw Gtr wasn't bothered at all...... neither were HEAPS of other cars.

Went out for a private track day at Lakeside yesterday with about 20 other cars (M3's, Aston Martin, Porche, 6L supercharged holden ute, commodores, GTST, 200 SX, etc, etc).

Gotta say the track is awesome compared to QR. No cars had any problems with the 92Db limit. My car (no side pipe) was 82Db on the drive- by (and was the loudest too by the way).

Whilst there are a lot more walls and barriers around the place, it is a very rewarding track. Main straight is a blast although the "kink" can be a little unnerving at high speed.

If you have never driven the track before (as was with me), I can highly recommend it.

Start off gently, get a couple of sessions in and before you know it you are going twice as fast as you think you can through some sections.

Hopefully they will keep it open forever, great track.

Didn't do any stationary 5000rpm tests - just fly-bys and the occasional take off.

There were some pretty growly V8's and the likes - mine isn't exactly the quietest of cars either.

None of which exceeded the readings at all.

Hey,

New to the forums and new to skylines, Just brought my self a R34 GT-V and have been looking for somewhere I can let loose legally.

I know what some of you are thinking, WTF u doing wanting to race a NA skyline for? well you have to start somewhere. and I have big plans for having one of the most powerful NA skylines around.

Anyway, I live on the coast so Im not too far away from lakeside. what are the requirements to be able to take your car out on the track?

Thanks

Hi Grunta,

If you want to get into track days, sign up at www.TimeAttack.com.au click the Join Now button at the top right and fill in the details.

To do sprints you need a road worthy car, long sleeve non flammable clothing (100% cotton like jeans and long sleeve shirt), covered shoes and a helment.

You will also need to purchase an AASA license to do Lakeside or Qld Raceway which you can get from the track admin on the day for $55

Paul

Didn't do any stationary 5000rpm tests - just fly-bys and the occasional take off.

There were some pretty growly V8's and the likes - mine isn't exactly the quietest of cars either.

None of which exceeded the readings at all.

Hey macca, the aston peaked at 94db on hard takeoff when the valves opened up, but was well under 92db on the main straight.

Cheers,

Shane

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...