Jump to content
SAU Community

Rb25det Afm S1 And 2

kurd_boi

By kurd_boi,
in Engines & Forced Induction

 Share

Recommended Posts

TTT Grand Master

TTT

Posted
Posted

because most R33's with RB25 engines are running near max voltage after 200rwkw.

at 220 that you want, they will be past their resolution.

and series 1 to series 2 AFM are slightly different. but still max out at the same level.

you are changing the afm. might as well start with the right one instead of having to change it again in the future.

dezz Grand Master

dezz

Posted
Posted
because most R33's with RB25 engines are running near max voltage after 200rwkw.

at 220 that you want, they will be past their resolution.

and series 1 to series 2 AFM are slightly different. but still max out at the same level.

you are changing the afm. might as well start with the right one instead of having to change it again in the future.

my car is making ~250rwkw on the stock afm :(

  • 3 weeks later...
TTT Grand Master

TTT

Posted
Posted
my car is making ~250rwkw on the stock afm :(

that's why I said most.

and did you tune it?

did you see it being tuned?

do you have a PFC hand controller where you can see the AFM voltage?

is it not hitting max (4.8 or whatever it is) way before redline?

You can tune the car still once it has passed max voltage..

but it's not as accurate.

which kinda defeats the purpose of having an AFM equipt car..

and it is kinda in the zone where you would want to place the most emphasis on getting the tune right.

  • 3 weeks later...
  • 3 weeks later...
James_03 Mentor

James_03

Posted
Posted (edited)
from wat i have read on here the R33 s2 pins , 2 of then are for grounding ! can anyone comfirm !

No thats not correct.

The S2 pink label R33 AFM has 3 terminals. With the AFM facing towards you and the flow arrow pointing ===> they are:

pin 1: 12v from eccs relay

pin 2: Ground

pin 3: Signal

The Green label R33 S1 AFM however uses 2 grounds. The first is an ECU ground, the second is a Chassis ground. This is the same scope and dimensions as a rb20det silvertop AFM, the terminal outputs are slightly different but both 80mm.

Here is something a found on the net ages ago that I dig up when I need it:

post-13028-1208908227_thumb.jpg

Edited by James_03

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a good German place in Brisbane if youre up for the drive 😛
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
×
×
  • Create New...