Jump to content
SAU Community

Detailing Day Before Wheels/shannons Day?

Michele

By Michele,
in Australian Capital Territory

 Share

Recommended Posts

CeJay Grand Master

CeJay

Posted
Posted
This worked well before Marques, should we do it again?

When?

Same place? (Donnan?)

Will the mighty Mick pike on us yet again and prove to be all talk and no action? oops did I say that out loud?

I'm in, depending on time and place.

Bullet32 Veteran

Bullet32

Posted
Posted
This worked well before Marques, should we do it again?

When?

Same place? (Donnan?)

Will the mighty Mick pike on us yet again and prove to be all talk and no action? oops did I say that out loud?

LOL, We'll see Michele :)

Donnan Collaborator

Donnan

Posted
Posted

Sorry everyone i haven't been near the internet for a while. My carpark should still be fine to use, i'll just have to clear it with the boss. I guess with the short notice it will have to be this sunday (9th) or next saturday (15). I don't think that i will be able to make it to the show with my car but i should still be able to have a sticky beak. I will see most of you tomorrow, so we can sort it out then!

Michele Veteran

Michele

Posted
  • Author
Posted
Is this a go or a no go? I'm ok for spending some time detailing the car on saturday.

It was a great day last time... I highly recommend to anyone thinking of going. I can't because I'll be a Wakefield with the FH.

Michele Veteran

Michele

Posted
  • Author
Posted
Oh so its ok for you to pike Michele... But not me?

SOFT!!

Nooo SOFT is not coming to the last one in the morning cos you had a birthday to go to that night... now thats SOFT.

There's a couple who have pulled out of the autosports day, anyone else wanna come?

CeJay Grand Master

CeJay

Posted
Posted

Since there only appears to be two interested including me, unless other people express interest, will go the detailing day off, will probably end up going to carlovers on Saturday morning or hand wash it then detail. It is a good day though to learn a bit off everyone else, in regards to detailing tips.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...