Jump to content
SAU Community

Recommended Posts

have you tested your o2's? you can do it using a voltmeter or using consult/datascan. you just need to make sure they're nice and responsive and that the voltage output should sweep from low to high about once a second. datascan or consult is easiest coz it will just display the voltage output for you. just make sure your car is at operating temp and you'll need to rev to about 2000rpm when you're measuring the voltages.

yea freind of mine hsa consult but he is currently at albury he should be back in bout 2 weeks il run the car thorugh that then. but it seems to be ok now, have to wait and run a full tank first to see.

he also has a NA zed :P

  • 3 weeks later...

how many o2 sensors need to be changed?, there that 1 that goes into extractors and another that goes into cat. change BOTH, or just the 1 that goes into extractors?!

Edited by OoskylineoO
how many o2 sensors need to be changed?, there that 1 that goes into extractors and another that goes into cat. change BOTH, or just the 1 that goes into extractors?!

There's only one O2 sensor (in the extractors), the one down near the cat is an exhaust temp sensor.

check out Kudos in the trader section for good cheap O2 sensors

There's only one O2 sensor (in the extractors), the one down near the cat is an exhaust temp sensor.

check out Kudos in the trader section for good cheap O2 sensors

I do not believe the sensor near the cat relates to how much fuel you use, I run my car without this sensor and it has no issues.

I also believe its a temperature sensor, not an O2 sensor....

im confused, how come it seems like the more i put my foot down, the better fuel econ it is??

the for past month, i been driving like a grandma and my car drank 10.8 - 11.2L/100km

but last week, i was having some fun in the car, and the car only needed 10.2L/100km.

can any1 tell me why?... and is it true that it saves petrol if you change gear at about 2000 revs?

too many variables for such a small difference.

are you measuring ambient temperatures while you're doing this?

the quality of the fuel?

how did you calculate the fuel usage?

for the whole time, i been putting in V Power.

i calculated by L of petrol divide by mileage, thats right...isnt it?...

  • 5 months later...

The draft Fuel Consumption Information Rule proposes that importers of light vehicles provide accurate and reliable fuel consumption information and seeks to clarify how this information is collected.

----------------------

williamgeorge

Used Cars

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...