Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

It reads *freight all up is around $110USD* lol

AHHHHhhh i see now! *opens eye's*

I haven't heard good things about cometic head gaskits, two of my mates (sss pulsar/rb25det) have both blown the gaskit, alos read some links about the sealing of cometic gaskits.. not so good.. . I'd be going tomei..

I've just ordered all my parts.

It ended up costing just under $1,700AUD landed.

CP pistons, 86mm, $759.99

ARP head studs, $257.95

Cometic head gasket (86mm, 1.2mm), $158.99

ARP main studs $165

ARP rod bolts $84.93

Freight to Australia, 3029 $105

TOTAL $1531.95USD

Add the 10% gst and the customs fee when it arrives.

Or get the supplier to give you a dummy invoice (less than $1k) and avoid all duties and taxes by clearing freight as a SAC.

There is no Customs fee.

Edited by 09ONE_32

Add the 10% gst and the customs fee when it arrives.

Quite often personal purchases aren't stopped in customs.

That said, even if I were to pay 10% GST on top I'd still be paying much less than the prices I got quoted within Australia but again, I doubt very much that there will be custom fees.

Yep, no doubt you're in front.

When I ordered my custom pistons from the states I forgot to ask the seller to change the value on the invoice. When they arrived they were held by customs and I had to clear them myself, pay 10% and a small customs fee. They were valued at US$1000.

There are fee's with a SAC too, not much, but they are exist. Unless its changed within the last 3 months.

Either way you will still be ahead a massive amount. The States is an awesome place to buy these kind of parts at the moment.

Yep, no doubt you're in front.

When I ordered my custom pistons from the states I forgot to ask the seller to change the value on the invoice. When they arrived they were held by customs and I had to clear them myself, pay 10% and a small customs fee. They were valued at US$1000.

There are fee's with a SAC too, not much, but they are exist. Unless its changed within the last 3 months.

Either way you will still be ahead a massive amount. The States is an awesome place to buy these kind of parts at the moment.

It'll be fine :P

*fingers crossed*

Yep, no doubt you're in front.

When I ordered my custom pistons from the states I forgot to ask the seller to change the value on the invoice. When they arrived they were held by customs and I had to clear them myself, pay 10% and a small customs fee. They were valued at US$1000.

There are fee's with a SAC too, not much, but they are exist. Unless its changed within the last 3 months.

Either way you will still be ahead a massive amount. The States is an awesome place to buy these kind of parts at the moment.

Yeah you lucked out with the $1kUSD on the invoice. If it was $999.99AUD then no duty or GST.

No Fee to lodge a SAC if you are a broker :D

Edited by 09ONE_32
I've just ordered all my parts.

It ended up costing just under $1,700AUD landed.

CP pistons, 86mm, $759.99

ARP head studs, $257.95

Cometic head gasket (86mm, 1.2mm), $158.99

ARP main studs $165

ARP rod bolts $84.93

Freight to Australia, 3029 $105

TOTAL $1531.95USD

are you able to say where abouts you got all these from?

are you able to say where abouts you got all these from?

Yeah sure, I got the parts from here: http://stores.ebay.com/Erics-Performance-Parts

If you just give him the quoted prices, he should match them (I did ALOT of shopping around and they matched the prices for me)

Check your pm's

i'll save you some money there :(

they also quoted me around 190-250us for postage, but max 4 days delivery

oops.. may have been a little too late on this one!

for everyone else...

http://www.horsepowerparts.com

have a whole selection of parts for rb's and their prices are cheeper than ebay

Edited by Angus Smart
Check your pm's

i'll save you some money there :thumbsup:

they also quoted me around 190-250us for postage, but max 4 days delivery

oops.. may have been a little too late on this one!

for everyone else...

http://www.horsepowerparts.com

have a whole selection of parts for rb's and their prices are cheeper than ebay

Good prices!

You can usually screw them down a little more if you call them and ask for their best price. I called a place over there when I was looking at brakes. A 6 piston brembo kit for a GTR with 355mm rotors was about USD$2900 or about $3200 AUD. I will be buying a set but not at this point in time. It helps that the Australian dollar is good against the green back at the moment too.

Good prices!

You can usually screw them down a little more if you call them and ask for their best price. I called a place over there when I was looking at brakes. A 6 piston brembo kit for a GTR with 355mm rotors was about USD$2900 or about $3200 AUD. I will be buying a set but not at this point in time. It helps that the Australian dollar is good against the green back at the moment too.

Delivery for those brakes would be a sh!tload though wouldnt it?

Got a link to the brakes ? :)

CP are a good piston, but unfortunately the same can't be said for the rings they supply with them

+1 on the rings

+1 again for JE rings.

I would suggest CP pistons with HKS rings or JE pistons with HKS rings.

Another option would be mahle rings. Just make sure you get the right ones for the pistons you buy.

With the rings, are all the brands using the same size rings? I need some new ones for my weisco pistons and wondering where to get some.

Also greg can you update us on how good the delivery from erics performance parts is, im about to buy from them if its all good.

Edited by GTR1993

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...