Jump to content
SAU Community

Recommended Posts

Hi all, been away from the forum for ages, but still saving the $ for my R34 4 door build (takes a while for a uni student), but getting closer :yucky:

Ive always thought (and have based much of my modification plans on) that the R34 GT-Four (NA AWD) runs the RB25DET gearbox.

Essentially the same as, or very similar to the R32 and R33 GT-R 'boxes, and the R33 Gts-t and R34 GTT 'boxes.

This gearbox should take the power from the RB26 with mild mods im planning on building and installing.

However after using the search fuction (thought id check before posting the question) I found a post that says that the R34 GT and GTV have the same 'box that the RB20DET R32s came with:

http://www.skylinesaustralia.com/forums/R3...&hl=gearbox

Which is a much weaker gearbox.

Doesnt make alot of sense to me, but car makers have done stranger things. :domokun:

Is it the case, that non turbo R34s came with a weaker gearbox than the GTT?

Or does the AWD version run the stronger gearbox despite being NA? ......(hopefully!)

Any info would be great! .....(and sorry if this is a repost of anything recent)

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/209266-which-gearbox-is-in-the-r34-gt-four/
Share on other sites

the gt-four runs the same box as r33 rb25det and r32-33 gtr, its just the bellhousing that changes

so when looking for a clutch you want a push type (the same as a r33 gtst)

it should hold the power just as well as a gtr :(

besides the rear diff...

Edited by R34GTFOUR
  • 6 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...