Jump to content
SAU Community

Recommended Posts

Ive been doing some searching on here about some short shifter kits

I really think nismo is the way to go

1. The kit says it reduced throw by 10%, is this even that noticeable, i used to drive a s15 and that had a much shorter throw than the 32

2. I also read on here that these kits wear out your syncros, is this true?? my gearbox feels a bit notchy going into 2nd, is this fixable

Link to comment
https://www.sau.com.au/forums/topic/209531-nismo-short-shifter-kits/
Share on other sites

I have one. I noticed a difference but it is harder to shift. I am thinking about taking it out. If you know some one with one and ask if you can see have a look. There is no need to drive around the block. Have a feel and see if you like it before spending the money

Mark

Edited by markiyq2

short shift kits are a lot harder on syncros because the syncros are designed to synchronize the gear speeds with the time taken in moving the factory throw... by shortening the throw you make quicker gear changes and therefor syncros do not have sufficient time to synchronize gear speeds...

havnt worded that real well but i hope you get what im saying :D

short shift kits are a lot harder on syncros because the syncros are designed to synchronize the gear speeds with the time taken in moving the factory throw... by shortening the throw you make quicker gear changes and therefor syncros do not have sufficient time to synchronize gear speeds...

havnt worded that real well but i hope you get what im saying :D

Nah. Sounds like a load of crap. :nyaanyaa:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...