Jump to content
SAU Community

Recommended Posts

thats exactly how a boost gauge works mate....below 0 is vacuum up to 0...then anything above that is displaying the amount of boost being used.....i have aftermarket gauge in psi and thats a lot more accurate from what i have found to stock gauges

is it normal that b4 i start the car pic1 turbo gauge showing 0- zero

and after car is running its going down pic2 but only to -0.6

month ago it was before i start a car in -1 and after -1 now it changed

is it a problem ??

thanks guys

Like most have said, it's normal for it to sit at 0 (atmospheric) when the engine is off, and for it to go negative when idle (the motion of the engine literally sucks air into it).

However, if the amount it goes down has changed and you haven't done changed anything (pod filter, boost controller etc), then you might have a leak. Does it still make the same maximum boost? (stock on the 34 is just over 3/4, or half way between 0 - 1) Does it hold that boost if you hold your foot down?

Like most have said, it's normal for it to sit at 0 (atmospheric) when the engine is off, and for it to go negative when idle (the motion of the engine literally sucks air into it).

However, if the amount it goes down has changed and you haven't done changed anything (pod filter, boost controller etc), then you might have a leak. Does it still make the same maximum boost? (stock on the 34 is just over 3/4, or half way between 0 - 1) Does it hold that boost if you hold your foot down?

i will check it and let u know but i think i yes its hold that boost.

i recently bought my skyline and i think its time to go to mechanic for inspection

will check my boost and let u know

thanks

just check it

working okay

its in 3/4 when hold foot down

thanks gosh no leaking

P.S. noticed another strange thing, sometimes boost gauge is stopping working (like the engine is turn off) anybody no how can i fix it ?? is it wire or gauge or what

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...