Jump to content
SAU Community

Recommended Posts

well when u drive it does it feel like its on boost. Rev out second gear to around 6000rpm and if you feel the turbo kicking in then obviously turbo not stuffed... Maybe its your gauge itself...

mate if you aren't too confident with tools just take it to a mechanic. either the gauge is stuffed (unlikely) or you have a dead turbo or a boost leak.

Dead turbo is easy for the to check but a tricky job to do (so don't try it)

Boost leak takes ages to find you could spend hours stuffing around.

So either way take it to the mechanic.

I noticed that with my car, but after close examination (and some "foot planting") figured my problem was my foot was to light. It's completely stock right? So you should start to feel it from about 3.5k rpm onward correct? you will notice the rpm's and speed climbs significantly faster. So, yeah it that doesn't work I would go see the mechanic. Remember to be safe when you hit the boost like adam said. Don't push it to far. Goodluck

Hey guys thanks for the replies. Yeah i've test it on a highway 0-80 and 0-100 the max the psi show is to "0" so i guess i'll have to take it to a mechanic. It does feel fast but it also feels that the car has been restricted.

I'm in melbourne any good places to take it for a check up? without getting ripped off?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...