Jump to content
SAU Community

Recommended Posts

Hi Guys,

I need to know where I can get replacement globes for my climate control...it still works but the backlight has gone. Also how do i go about changing the lights in the climate control

I guess if you follow the diy for removing the head unit you will get there.

did the bulbs die after the Headunit install? Chef_stage's did and we left it 2 or 3 days and they decided to start working again?? :S good luck!

Well one was already blown but when i installed my head unit the other side blew out

Don't worry Jason if you can get your stereo out then this should be an easy fix!

Probably covered elsewhere on site but I had this handy so took some photos for you...

Step 1 pull the climate control out - 4 screws, two on each side hold it to the bracket. NOTE I left the bracket attached and didn't remove those screws. Here then is the complete assembly:

post-32445-1205167406_thumb.jpg

If you look at the back of it you can see the 6 globes straight away - easy!

post-32445-1205167470_thumb.jpg

6 in total, 4 at the bottom behind the buttons, 2 at the top (I presume for the backlight). The 4 down the bottom are of one type, the two at the top are another. Close-up of one of the bottom ones:

post-32445-1205167477_thumb.jpg

Close-up showing the location of the two at the top (backlight):

post-32445-1205167484_thumb.jpg

You simply use a flat-bladed screwdriver (or small Phillips) and they take about a quarter-turn to undo.

Here are the globes themselves, showing the two types. One on the left is the backlight one (I think, someone correct me if I'm wrong!) from the top (two the same). The one on the right is the type used for the 4 lower bulbs (for the buttons):

post-32445-1205167491_thumb.jpg

As for finding replacement globes... I can show you what they look like but I haven't investigated replacements... anyone else recognise them from the pic's? There was a user on SAU selling LED versions of these bulbs for skyline/stagea, think it was 666dan ?

I had some bulbs out on my stagea, went to dick smith and had look at the bulbs they had there. I found some that were 12v, they were physically smaller than the originals and had yellow wires on them already which i had to remove. Even though they are smaller you can still put the little blue covers over them. Sorry for the lack of detail but it was a while ago... Point is you can get similiar bulbs from dick smith that will work with a little bit of mucking around. They have lasted for a couple of years now, no problems.

Edited by deano_33

I picked some up from repco a couple of weeks ago for the climate control.

They are listed in the navara or austa globe catalogue.

They are the same as the smaller globe on the left in DaveB pic.

I used them in all sockets on the climate control and it lights up fine, it appears you dont have to worry too much about having the longer globe as the shorter ones light it up fine.

I'll put a pic up later this evening after work and hopefully a part number so you dont have to trawl the the catalogue and match them up like i did.

I used them in all sockets on the climate control and it lights up fine, it appears you dont have to worry too much about having the longer globe as the shorter ones light it up fine.

I'll put a pic up later this evening after work and hopefully a part number so you dont have to trawl the the catalogue and match them up like i did.

Sweet! thanks

I had some bulbs out on my stagea, went to dick smith and had look at the bulbs they had there. I found some that were 12v, they were physically smaller than the originals and had yellow wires on them already which i had to remove. Even though they are smaller you can still put the little blue covers over them. Sorry for the lack of detail but it was a while ago... Point is you can get similiar bulbs from dick smith that will work with a little bit of mucking around. They have lasted for a couple of years now, no problems.

That sounds like a "grain-of-wheat" globe, like this:

p8140.jpg

Standard long-legged 12 volt incandescent.

Here are the globes themselves, showing the two types. One on the left is the backlight one (I think, someone correct me if I'm wrong!) from the top (two the same). The one on the right is the type used for the 4 lower bulbs (for the buttons):

post-32445-1205167491_thumb.jpg

As for finding replacement globes... I can show you what they look like but I haven't investigated replacements... anyone else recognise them from the pic's? There was a user on SAU selling LED versions of these bulbs for skyline/stagea, think it was 666dan ?

can you removed the blue part - i've got some t5 wedge 3 led globes (mate brought 1 too many sets for his dash) but looks like I need the holder to put them in the climate control...so can you still use the grey bit or can you buy wedge holders to fit

Do you mean the blue plastic rubber cover? Pretty sure that can be removed.

If you mean the bulb itself; I'm not sure. You could almost definitely just cut the legs off it and solder the LED's legs underneath; I will take a look when I get home. How are your LED's terminated? Do they have 'legs' (for what I mean by legs see pic' above showing "grain-of-wheat globe" - they are the solid - but flexible - silver wires sticking down underneath).

Hi All,

Sorry for my rather delayed reply.

Here's the pics of the globe i used.

No number stamped into them so, you'll have to compare to the catalogue unfortunately.

Also forgot to mention in original post, the globe height was a tad to tall for one of the

far left or right sockets (im forgetfull), so i used my drill press to drill down into the clear plastic

diffuser within the socket about 1-2mm which made for perfect fit.

I see people chatting about those blue rubber covers, they were all in my climate control originally

before the bulbs started to blow, gave a grey look to the display not really blue colour at all.

I rekon those grain of wheat bulbs would give similar look given it's a lightish blue.

Also found those original grey globe holders in the climate control were real easy to unwind the wires with a small pick. Then replace with new bulbs, plenty of wire to work with and small needle nose pliers to pull wire tight, plug'em back in and off you go.

Have'nt check out blue leds myself but been thinking about it for a while now.

Normally leds dont have a nice fine wire to thred through the grey globe mount holes,

also wires are fairly inflexible and wouldn't be long enough as they are usaully for

soldering to a pcb. Standard size led diameter is also too big for the original grey mount.

Although in saying that when i've pulled apart various electrical & pc equipment I've seen some tiny

leds that would be a great fit, just solder some wire to the legs for extra length and thread through.

Which leds are already made to fit? was it those t5/t10 leds i dunno? there's a thread on it someone is selling them.

post-38314-1205930684_thumb.jpg

post-38314-1205930705_thumb.jpg

post-38314-1205930718_thumb.jpg

Edited by Stagea_Neo

Thanks Stagea_Neo :down: re: LED's; the LED devices themselves come in a variety of diameters/sizes, among the most common sizes are 5mm diameter and 3mm diameter, so I believe they could almost definitely be made to fit. They always have long legs too (when they are installed on a circuit board the legs are cut short) which would reach through the socket to the base. Saying that you could not simply connect each LED directly to the socket without a current limiting resistor in series with each LED (unless you have a T5 globe or something like that, which has been designed with a current limiting resistor built in); 1K ohms for a 20mA LED should be about right by my calculations (based on 13.8V) but you should probably check this. A big range of colours/hi/low brightness options and low price (about 20 cents each) means I will probably go LED's soon as I think they could be installed relatively easily with the aid of a soldering iron.

  • 2 weeks later...
the lights I got are these ones

post-34764-1206492556_thumb.jpg

is these the rights ones??

Sorry, wasn't able to answer this question, but did they fit?

I have just found some info' on globes for the (standard) climate control:

A/C Unit

- 2 x T5 multi direction/3 LED bulbs (the one you can see in the bulb holder in the DIY) These i used in the LCD of the A/C

- 4 x T1.5 Single LED bulbs (smaller and as you can see in the pics the A/C buttons are not very bright. But still great!

This was from this thread under the DIY sticky:

http://www.skylinesaustralia.com/forums/in...t&p=3333939

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...