Jump to content
SAU Community

Recommended Posts

Hi guys I can get brand new real carbon fibre R32 GTR grills for about $260 or normal fibre glass grills for $150.

The grills are all brand new. Depending on how many people are interested in this group buy will depend on how much cheaper I can get them.

Ok I have been told I i have to put a close date so I will make it a month from now 11/April. The grills will be imported from the US there will be no GST or custom dutys as the value of the grills are less then $1000US

Postage will be be included in the price and the grills will be sent direct from the supplier to each individual person.

Let me know if you want to be put on the list. As it gets to the closer to the close date I can get the exact price of the grills as I will have a better Idea of how many I will need to get.

Cheers

1. MYSELF

2. BWRGTR

3. JM4MP

4. J-TRAIN

5.NEFRET

post-17649-1205196373_thumb.jpg

post-17649-1205196379_thumb.jpg

Edited by boosted_32
i wouldnt mind seeing a photo of the carbon installed on a gtr...

i'm semi interested!

ive got a carbon bonnet on my car so I recon the carbon grill will look awsome!

  • 1 month later...

Remove from list please.

I was banking on the close date being the 11th of April and I still have not heard anything.

Have taken another quicker avenue.

Organisation please.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...