Jump to content
SAU Community

Recommended Posts

Hey guys

Last week i was speaking quickly with someone about how i can make an RB26 block stronger, we didnt get into price or anything like that though.

Ive bought another RB26 motor that over the next little while ill be building for big, big power

Who here has done the resin filled block? Any words of wisdom from those guys would be great :pirate:

Another thing thats on my mind about it - is it going to be more effective to resin fill an 05U block than rather just getting a 24U block and using that without resin?

Lastly - how much does the process cost?

Cheers guys :D

Link to comment
https://www.sau.com.au/forums/topic/210084-rb26-resin-filled-blocks/
Share on other sites

Yeah, dont worry mate, the only part ill have to do with is paying the bill and driving it

But still have virtually no info on the actual process, benefits (compared to buying a 24u block), costs etc

Benefits will depend on how far you fill it. You can still street drive it if you only fill to the bottom of the water pump. If you fully fill it its only drag after that. Just make sure its washed out with acid to give a good surface for the resin to adhere to. Also depending on the product you use, you may have to line bore the block to get it all square, but that depends. Its a good idea tho if block rigidity of the lower section needs to be better. Price I cant remember what i was quoted, but i know the block is supposed to sit for a substantial time after filling.

Edited by GTR1993

Ive done a few rb blocks using Hardblok which is designed to have the same expansion rates as cast iron and is very permanent. Ive done 1/4 fills and 1/2 fills. The 1/4 fills seem fine on the street as far as cooling is concerned. The 1/2 fills have been done for the drags so I have no idea how they fair for a daily driven car but I'd imagine they would cope fine. Hardblok is just like tile cement and you mix it with water using a power drill with a paint mixer attached. I use a small funnel that I jam into water gallery holes in the top of the block then just pour it in a bit at a time and work it in with some wire. Once you've poured some into each hole you can just work it all the way around the cylinders with the wire. Its messy crap and bit of a pain to do but its not that hard to do it yourself.

Ive done a few rb blocks using Hardblok which is designed to have the same expansion rates as cast iron and is very permanent. Ive done 1/4 fills and 1/2 fills. The 1/4 fills seem fine on the street as far as cooling is concerned. The 1/2 fills have been done for the drags so I have no idea how they fair for a daily driven car but I'd imagine they would cope fine. Hardblok is just like tile cement and you mix it with water using a power drill with a paint mixer attached. I use a small funnel that I jam into water gallery holes in the top of the block then just pour it in a bit at a time and work it in with some wire. Once you've poured some into each hole you can just work it all the way around the cylinders with the wire. Its messy crap and bit of a pain to do but its not that hard to do it yourself.

when u say 1/4 or 1/2 filled, where on the block are those measurments? i.e is 1/4 filled to the bottom of the welsche plugs?

Benefits will depend on how far you fill it. You can still street drive it if you only fill to the bottom of the water pump. If you fully fill it its only drag after that. Just make sure its washed out with acid to give a good surface for the resin to adhere to. Also depending on the product you use, you may have to line bore the block to get it all square, but that depends. Its a good idea tho if block rigidity of the lower section needs to be better. Price I cant remember what i was quoted, but i know the block is supposed to sit for a substantial time after filling.

Needs to be street driven, what sort of time would you call substantial? Days/weeks/months?

Ive done a few rb blocks using Hardblok which is designed to have the same expansion rates as cast iron and is very permanent. Ive done 1/4 fills and 1/2 fills. The 1/4 fills seem fine on the street as far as cooling is concerned. The 1/2 fills have been done for the drags so I have no idea how they fair for a daily driven car but I'd imagine they would cope fine. Hardblok is just like tile cement and you mix it with water using a power drill with a paint mixer attached. I use a small funnel that I jam into water gallery holes in the top of the block then just pour it in a bit at a time and work it in with some wire. Once you've poured some into each hole you can just work it all the way around the cylinders with the wire. Its messy crap and bit of a pain to do but its not that hard to do it yourself.

Thanks for that, i wont be doing it myself though

From the 1/4fills have any of those blocks failed? I assume they're all running big power

How much power are you realistically looking at making?

On a side note.... Looks like I aint selling my gt block to anyone!!!! :D

450 awkw and ill be happy

You can bore a block 24hours after using Hardblok and use it straight after that. The 1/4 fill block runs low 11 and is daily driven. It was mainly done to stop oil getting into the water not for overall strength like the 1/2 and 3/4 fill blocks.

Cool thanks :D

When i talked to a place in Adelaide (rhemac) they liked to leave it for weeks, i looked on the net and some people like to leave it for months!

http://www.mustangsandmore.com/ubb/Forum12/HTML/008073.html

Im not sure how long it must be left tho.

A 1/4 fill is pretty much the bottom of the welsh plugs. The main reason we did this is that we found that some blocks were cracking internally between 3 and 4 where an oil gallery runs from one side of the block to the other causing oil to mix into the water.

Would this be why some rb26 blocks leak coolant out the side above the oil outlet hole?(which is between 3-4) May explain why my radiator fluid looks like the Exon Valdize shipping lane and the coolant out the side of the block.

btw. I'm not to fussed as I'm building a RB30/26 but I've seen a few rb26 motors with the leak out the side so this is quite interesting. :thumbsup:

I hope the rb30 doesn't have the same issue.....

I have seen and heard of many rb26 blocks that crack both internally and or externally which is the reason most people look for the stronger N1 blocks.

Ive only used the Hardblok product and usually leave it for a week before machining but they say it can be used after 24 hours.

As far as the rb30 blocks are concerned they dont seem to suffer from the same problem but I have heard of them cracking between 5 and 6 under extreme loads. Ive seen some guys make up a plate that bolts toward the rear of the block for added strength. I would imagine that when the rb30 block is used with a rb26 sump and adapter plate that this would add some strength to that area anyway. Ive just done a 30 block for a gtr which should push over 1000hp so I added a 1/2 fill of Hardblok for a bit more security. Being an all out drag car cooling shouldnt be an issue.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
×
×
  • Create New...