Jump to content
SAU Community

Big Ends R32 Rb26dett

PHA71L

By PHA71L,
in Engines & Forced Induction

 Share

Recommended Posts

Duncan Grand Master

Duncan

Posted
Posted

well it might be actually possible, would need subframe off, sump off, crank out, balancer off, timing gear off, timing belt off, oil pump off, gearbox off, clutch off and flywheel off.

but if you did all that you could probably get to all of the bearings.

seriously though, if you need new big end bearings, rebuild the motor. the main bearings are probably in trouble, there is most likely some crap floating around somewhere, might as well do a hone and new rings while you are in there. pull it apart, clean and check it all, put it back together. so much damn work just to get the sump off

SLED Grand Master

SLED

Posted
Posted

You wouldn't have to remove your crank to change B/E brgs. I've changed them on various other motors in the past by removing the B/E caps & spark plugs, pushing each piston up an inch and being real careful not to nick the journals with the thread on the B/E bolts, if you do, crank has to come out (might have to come out anyway for a grind or at least a linish if its got grooves).

You'll have to do a r & r on each cyl that's on the down stroke then turn crank to do others.....pretty messy this way but good oportunity to replace with a decent baffled sump.

As far as mains are concerned, they rarely fail unless there's crap in the galleries but usually evident by pitting or scratches on the B/E shells.

MYRB30 Rising Star

MYRB30

Posted
Posted

You CANNOT get the sump off with the gear box attached, there are two bolts behind the flywheel. This has been covered before, It is not practical to take the box out, to remove the sump. Just pull the engine, there is no way around it. And yes, I have done it.

Sorry to be a spoil sport

PHA71L Community Regular

PHA71L

Posted
  • Author
Posted

ok thats fine.... just wanted to find out first as i have never worked on a rb26 befor motor has only been rebuilt not long ago.... it got low on oil and now has the knock at around 3 4000 ill get some one to do all the work and check every thing

might be time for the bigger turbos at the same time :domokun:

SLED Grand Master

SLED

Posted
Posted
You wouldn't have to remove your crank to change B/E brgs. I've changed them on various other motors in the past
You CANNOT get the sump off with the gear box attached, there are two bolts behind the flywheel. This has been covered before, It is not practical to take the box out, to remove the sump. Just pull the engine, there is no way around it. And yes, I have done it.

Sorry to be a spoil sport

Fair enough, its good info to know. As I stated above, I have removed sumps on various other motors whilst still in the car but not on an RB, thanks.

SLED Grand Master

SLED

Posted
Posted
yes so have i thats why i asked.....it has cp pistions and a baffled sump ect all ready and light weight rods im not sure what type of bearings were used tho any ideas on how to tell?

Check numbers on the back of the shell, may give a clue, or if your not using them again light scrape on inside will tell you if they're copper leads or alu tins. Always a good idea to use a copper lead or similar in an RB though.

blind_elk Grand Master

blind_elk

Posted
Posted
Huh??? Same thing....you gotta remove the B/E cap to remove the B/E brg. What sort of other B/E is there?
Where do you think the big end bearing sits, and what does it protect? The Big End (it's the end of the conrod that connects to the crankshaft).

If you are referring to the big end bearing, then call it that.

SLED Grand Master

SLED

Posted
Posted
Where do you think the big end bearing sits, and what does it protect? The Big End (it's the end of the conrod that connects to the crankshaft).

If you are referring to the big end bearing, then call it that.

Been in the engine reconditioning game for 20 years mate so I appreciate you teaching me something that I learnt when I was still in nappies.

When engine reconditioners say they're changing their B/E's, they're always referring to shells. Otherwise they refer to the rods specifically. They never talk about changing B/E whilst referring to rods.

Sounds like you like to make a play on peoples words and argue pointless issues otherwise you wouldn't have asked such an obvious question.

blind_elk Grand Master

blind_elk

Posted
Posted
Been in the engine reconditioning game for 20 years mate so I appreciate you teaching me something that I learnt when I was still in nappies.

When engine reconditioners say they're changing their B/E's, they're always referring to shells. Otherwise they refer to the rods specifically. They never talk about changing B/E whilst referring to rods.

Sounds like you like to make a play on peoples words and argue pointless issues otherwise you wouldn't have asked such an obvious question.

Sorry, didn't realise you had so much experience in these matters.

Yes, I can be a pedantic old bastard sometimes. It's just that there are quite a few younger members who don't always understand the technicalities.

And the only stupid question is the one you don't ask.

SLED Grand Master

SLED

Posted
Posted
Sorry, didn't realise you had so much experience in these matters.

Yes, I can be a pedantic old bastard sometimes. It's just that there are quite a few younger members who don't always understand the technicalities.

And the only stupid question is the one you don't ask.

Yeah no probs bud, I know what you mean & I agree, its like banging your head on the wall sometimes. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • GTSBoy
      R33 persistent issues. P/steering and lag/misfire

      By GTSBoy · Posted

      What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
×
×
  • Create New...