Jump to content
SAU Community

Recommended Posts

  • Replies 171
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I wouldn't mind tagging along to this since i don't have work on fri :blink:

Would there be alot of police troubles at that area?. As the last time i was there for that 'big boys toys' thingo...there was a defect station set up. :thumbsup:

This meet place is not at Chadstone shopping centre itself. It is further down the road in a park park solely for the Harvey Norman store there which will be closed at the time of meet. I know the night you were refering too. This is not a major event that will attract the same attention as that night. We shouldnt have issues as long as noone "misbehaves" and draws in attention to us. Plus we wont be there the whole night. We will be moving for food and photos.

yep - 8.30 pm - i might wash the car before hand too - but at my usual place on springy road (opposite century city)

and yes - as long as there arent people misbehaving - we will be fine

and as for duck - i got an email that perhaps some of you might want to look at - turns you away from Rock Kung Restaurant :thumbsup:

LOL hahah yeah I am! I'll try and see if I can take out the 32 though. There will be 3 four door 32's on the night if I can. Highly doubt it though. :)

haha try to bring it - I might bring mine out but but hesitant due to cops

Shouldn't be a problem man, there will be 10+? cars coming on the night, chances are they'll pull someone elses car over instead of yours. I wanna check out your car!

I'm in a pretty tight position if I take out the 32 as well. Cops pull me over and then BAM 3 demerit points gone. :)

Shouldn't be a problem man, there will be 10+? cars coming on the night, chances are they'll pull someone elses car over instead of yours. I wanna check out your car!

I'm in a pretty tight position if I take out the 32 as well. Cops pull me over and then BAM 3 demerit points gone. :)

mate im in the same position. only i've already lost 3. so BAM licence gone

Shouldn't be a problem man, there will be 10+? cars coming on the night, chances are they'll pull someone elses car over instead of yours. I wanna check out your car!

I'm in a pretty tight position if I take out the 32 as well. Cops pull me over and then BAM 3 demerit points gone. :)

bahaha yeah

maybe if I get my ECV hooked back up tomorrow night and tidy up the vac lines I might bust it out for a bit - I'd only come to the car wash though

mmm might come along actually

Shouldn't be a problem man, there will be 10+? cars coming on the night, chances are they'll pull someone elses car over instead of yours. I wanna check out your car!

I'm in a pretty tight position if I take out the 32 as well. Cops pull me over and then BAM 3 demerit points gone. :)

bahaha yeah

maybe if I get my ECV hooked back up tomorrow night and tidy up the vac lines I might bust it out for a bit - I'd only come to the car wash though

mmm might come along actually

the fronts high but, I had to raise it so I could actually drive it - now I'm embarrassed to drive it lol

bahaha yeah

maybe if I get my ECV hooked back up tomorrow night and tidy up the vac lines I might bust it out for a bit - I'd only come to the car wash though

mmm might come along actually

the fronts high but, I had to raise it so I could actually drive it - now I'm embarrassed to drive it lol

ahahaha, I wouldn't be embarrassed driving a car like that, chances are people won't even notice the height. Bring a c-spanner on the night and we'll lower it a bit more before taking photos. :yes:

My car's low as again, I lowered it a bit more over the week end. So now they're 8kg/mm up front, but as low as they were in the photos I showed you a couple months back. :)

mate im in the same position. only i've already lost 3. so BAM licence gone

So you're not allowed to drive turbo? Or is this under the other law how you're not supposed to drive a car more than 125kw/tonne?

I'm assuming the old rule though. Bad luck. :)

I swear Easter is in April but Im not complaining LOL!

This sounds good!

Special LILKAAAY!

You get ya car buddies and girls down there too!!! :)

yeah gonna come down with alex and tim again.. My gfs want to see the easter bunny =]

the fronts high but, I had to raise it so I could actually drive it - now I'm embarrassed to drive it lol

Mine is like a Skyline truck anyway, so yours will look like its sitting on the ground compared to mine.

:P




  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...