Jump to content
SAU Community

Looking For A Plain Carbon Fibre Bonnet, Are They Legal?

beRwick_GTRage
 Share

Recommended Posts

NickR33 Grand Master

NickR33

Posted
Posted

the bonnet has nothing to do with crumple zones or any accident stuff it is just a lid to stop water getting on your motor so you may change it for carbon or fibreglass... providing it doesn't have any 'protrusions' like vents etc that may stop a pedestrian from rolling over the bonnet in the case of an accident

this is what I have been told by someone who does roadworthies for a living... but I can still imagine you copping grief from the boys in blue... depending on where you live

babyskyline Grand Master

babyskyline

Posted
Posted
but saying that....www.carmate.com sell them and im sure most if not all bodykit places would sell them

If you read http://www.carmate.com/termcondition.php about 2/3's of the way down there is a line saying:

All parts forsale at Carmate are recommanded for Show Conditions, not for Legal Street Used purposes.

Just because they sell them on their websites doesnt make them legal for street use.

As far as i know carbon bonnets are 100% illegal for street use. There are no ADR approved ones available as of yet but that may have changed recently.

Owgasm Grand Master

Owgasm

Posted
Posted
I'm confused.. doesn't the r34 gtr vspec 2 comes with carbon fibre bonnet? Does that also makes them illegal on the street even though its from factory?

Could possibly be that they are illegal in australia, even though its from factory but when going through compliance to make it Australian standard, a aluminium one is put on and then replaced after registeration.

Yawn Mentor

Yawn

Posted
Posted (edited)

Anything factory is almost always fine, look at all the exotics going around with their factory loud exhausts.

The reasoning is that its all engineered correctly unlike some cheap carmate one

Edited by Yawn
NoFX_Hardcore Proficient

NoFX_Hardcore

Posted
Posted

If you're in QLD, I can personally vouch that carbon bonnets are illegal as I got done twice in 8 days...

However, you can definitely get some aftermarket bonnets engineered... Carbon fibre ones can be engineered but they have to be sent away for crash testing so if you want it engineered you have to get two... Expensive and not worth it considering the fine is only 1pt and 75$.

JDM032 Experienced

JDM032

Posted
Posted

just dont drive like a hoon and u wont get pulled over as much n they mite leave u alone.

i got screamer n loud exhuast n bells n whistles here and there n if a cop is next to me i smile and drive normally.

its all ya gotta do but i understand they have bad days too.

but yeh carbon is definately illegal coz if u have a head on the bonnet doesnt bend it stays as one and can push bak through the windscreeen and behead with you lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...