Jump to content
SAU Community

Recommended Posts

Hey guys i have a R33 GTST and i installed a Z tune style bonnet on there and today it was pissing down with rain and i think that some water has go into the spark plug hole because its sounding like a WRX and just keeps misfiring? so im just wondering if i take off the spark plug cover and clean up all the water will the car run back to normal? would anything happen to the spark plugs?

Cheers

Chi

Link to comment
https://www.sau.com.au/forums/topic/212851-water-in-spark-plug-area/
Share on other sites

water wont get in the spark plug hole unless youre spark plug wasn't in properly... it could have got down and shattered the ceramic on the spark plug... but i doubt it... could be a a spark plug has gone (through use) or even could have got water in the air intake... is your filter inclosed? and is there a vent near it??

Yep its the vented bonnet "I got rained on and my coil pack cover isn't water tight" sound...

The hard part is getting the water out, I used a long piece of clear hose and gravity to drain the water...

Afterwards make sure the rubber seal on the coil pack cover is on straight and sealing properly, I leave the back of the coil pack cover loose to let heat out so my splitfires don't get overheated.

The water will evaporate but its not advisable to do it that way...

hmmm well its not in the hole im just saying it could be sitting like aroudn the spark plug? mmm perhaps some CRC and alot of rags to drain the water :glare: mmm it doens't have a vent for the air filter part but yeah ill see tomorow perhaps its time to invest in a new filter :D

Cheers

Chi

what new filter, the water is nowhere near your air intake? An I missing something?

its sitting around your spark plugs and making them arc...

The ztune style bonnet has vents directly above the coil pack cover, thus why making sure your coil pack cover seals are installed correctly will resolve the issue for the future...

as long as the coil pack cover is sealed there is no problem... I too have a vented bonnet and had the same problem at first since I didn't run a coil pack cover at all... sealed it and all is good...

Tighten the screws I believe is what he means.. Otherwise silicone would work but surface would have to be cleaned extremely well (if you wanted more protection) Alternatively find some silicone boost hose split it up one side and slide it down the sides of the cover and glue together at each end and screw down should do i decent job if you get it in right

Hey guys i have a R33 GTST and i installed a Z tune style bonnet on there and today it was pissing down with rain and i think that some water has go into the spark plug hole because its sounding like a WRX and just keeps misfiring? so im just wondering if i take off the spark plug cover and clean up all the water will the car run back to normal? would anything happen to the spark plugs?

Cheers

Chi

where did you get the bonnet im looking for one at the moment!

I hear they are really bad for getting water down in there and it will wreck your motor....i will give you $200 for it :(

hahah ur wishing :ermm: hmmm just go tanother question....i have cleaned all the water out of the spark plug area boosts fine until 5k it starts misfiring perhaps if i replace the spark plugs it will be all good??

Cheers

Chi

hahah ur wishing :ermm: hmmm just go tanother question....i have cleaned all the water out of the spark plug area boosts fine until 5k it starts misfiring perhaps if i replace the spark plugs it will be all good??

Cheers

Chi

Where did you get the bonnet?

Probably worth taking it all out for a day to let it dry out i think you can bugger your coil packs getting them wet just like most electrical things they can get wet but its the corrosion that will kill them in the end!

My GTR has a vented bonnet also, When it rains it scares the hell out of me.

I have no gargage so i put a car cover over my car, I am sort of lucky the water hit's the fan so it's really not going on the top of my engine lucky because i have no engine covers.

water can get in the electrical plugs( cas connector) and cause the same problem. but sounds like u need new plugs or coil packs.. most ppl dont run the coil pack cover to stop them getting as hot.. but then if u dont, u get the problem with water.. but thats easily fixed compared to the price of a coil pack

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...