Jump to content
SAU Community

Recommended Posts

hey guys!

just purchased myself a cooling pro stealth fmic (600x240x60) and have just installed it today after a few hours. the only hacking i needed to do was a little bit of the intrusion bar to hug around the corners of the fmic and the hacking of a support bracket on the bottom pipe (would not give me that little extra room to line it up with the stock piping no matter how hard i huffed and puffed).

my warning is mainly for series 2 owners - the first bend of the top pipe prevents your front bar (that is, if you have stock) to go on properly due to the fog light and the housing on the left side (looking at the front of the car). i thought i could hack the housing on an angle but realised it was also the rear of the fog light that actually hit the bend as well and thus i could not line up the right side (looking at the front of the car) of the bumper. hacking the housing that was built into the bar is one thing, but hacking the actual housing for the fog light is another.

after an hour sitting in my thinking chair, i decided to remove the stock fog lights + indicator assembly and hack off the housing built into the bar itself to allow room for that damn bend! now i had the problem of an ugly space where the fog lights + indicator assembly should be, so what i did was pop down to autobarn and bought myself a grill mesh and then bought gtr look-a-like indicators and fog lights. what i did was fill up that gap for the assembly with the grill and just cut out holes to fit in the new indicator and fog light. i left the bottom half as stock so basically, rather then having the fog light + indicator assembly, i now have a grill with a fog light and indicator - pretty much a 400R front bar imitation.

just a note - most or some other fmic piping actually go UNDER the fog light + indicator assembly. just weird when i encountered this problem. had me scratching my head for hours taking apart random things and putting them back in thinking i alligned something off.

APART from that debacle, no problems thus far. im quite happy with the fmic. its definitely living up to its stealth because the bottom pipe hides directly behind the bottom section of the front bar and the core itself is actually hiding behind my plates. only noticable if you look hard enough. i get no turbo lag since the pipes use the existing stock pipes so you get the shortest cooling route possible. i have installed 3 other types of fmic(s) and after a test drive the boost does take longer to pick up speed. with this setup, it spools maybe a little faster if not the same. bottom end rpms have alot more pick up (a little but noticable).

i can only assume, but this kit was really meant for the series 1 owners since their bar has more room behind it but anyone with an aftermarket front bar should have no problems.

hope this helps some of you s2 owners thinking of getting one of these.

Link to comment
https://www.sau.com.au/forums/topic/214746-cooling-pro-stealth-fmic/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey , Dude thanks. I was about to buy one! i use to have a BLitz LM and i sold it for 1,000 but now i want it bak! :D i only had it for a week !!!!!!!

also could you please post up pics plz :O

Edited by geraus
Hey , Dude thanks. I was about to buy one! i use to have a BLitz LM and i sold it for 1,000 but now i want it bak! :D i only had it for a week !!!!!!!

also could you please post up pics plz :rofl:

Is it me or does this make no sence? :P Why buy a Blitz to sell and get a Stealth? Unless you were after some $? Hehe.

Im guessing, in this case if your like me and have an S2 with a different OEM bumper (pictured) Then possibly you wont have the same effects? As there looks to be bugger all behind the indicator, heeeeaps of room. Can only buy one and try i guess!

post-38698-1208149376_thumb.jpg

hey guys!

just an update, i ended up cheating after all because i did not like the look of the mesh - too much attention in my opinion as i like to keep my car as stock looking as possible. i ended up fitting in the stock lights with some very minor modifications to the assembly. here is just the one picture of the whole thing and i apologise for the poor quality. if anyone wants to see the actual modifications up close just post here and when i am free i will take pictures so you can see up close what i did. i did not take pictures of the grill because i was not going to keep that look.

post-32455-1208154486_thumb.jpg

as you can see, most of the fmic hides under the front bar which in a way gets less wind but since its winter i do not think its a problem thus far although since the fmic is rather wide it may make up for that loss in height. i will have to wait for summer and see how it handles. other fmic(s) i have installed uses the bottom pipe area for extra height for the core (hence why the bend usually goes under the fog light + indicator assembly).

i thought about it today and looked at black warriors tutorial (which was a big help by the way) and noticed that since his core was actually shorter in width than mine, the bend that gave me trouble actually bends earlier to hug the corner straight under the head light. the cooling pro actually bends later or else the piping diameter is comprimised! just thought some people would appreciate an answer to why as i hate not knowing why haha.

Nice paint job on your bar.

was this aimed at me? and are you refering to the sun reflection? as my front bar is in great factory condition.

Edited by Silver_R34_GT-T

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...