Jump to content
SAU Community

Pod in Stock AirBox

Guest Robo's

By Guest Robo's,
in General Automotive Discussion

 Share

Recommended Posts

Guest Robo's

Guest Robo's

Posted
Posted

Ive got a Apex pod filter, and agree im defeating the purpose of having hot air go into the turbo and then get pushed out at a much hotter temperature, then letting the stock cooler trying to cool it, before going into the plenum.

So why not trying to reduce the air coming into the turbo through a cold air system. I dont want to cut any holes, so i thought get a stock box with the over the radiator duct and try and hack the box to make the pod fit. Then try and have another cold air duct enter the box from underneath or something, probably only room for a small tube.

Anyone done something like this?

Link to comment
https://www.sau.com.au/forums/topic/21548-pod-in-stock-airbox/
Share on other sites
sewid Grand Master

sewid

Posted
Posted
Originally posted by Champinco

i have a qn..im new to this whole POD thing. all i know is that i have an HKS POD with a HKS big intercooler. would i or do i have to partition off the POD???  (put a box surounding around it?)

Cheers

Yes. Otherwise you should go back to the stock airbox.

A pod filter with no partition will cost you performance every time.

See this thread: http://www.skylinesaustralia.com/forums/sh...&threadid=13003

sewid Grand Master

sewid

Posted
Posted
Originally posted by Robo's

Anyone done something like this?

Thought about it but have you actually ever pulled the airbox out? It is far too small to fit a pod filter inside and if you could find a pod filter that small it would actually reduce performance due to friction, and generally a lower filter surface area than the stock panel.

I then thought of building a fiberglass box that would take the stock airbox lid and fit a pod filter inside.

That seems to be a better idea maybe.

Guest Robo's

Guest Robo's

Posted
Posted
Originally posted by sewid

Thought about it but have you actually ever pulled the airbox out? It is far too small to fit a pod filter inside and if you could find a pod filter that small it would actually reduce performance due to friction, and generally a lower filter surface area than the stock panel.

I then thought of building a fiberglass box that would take the stock airbox lid and fit a pod filter inside.

That seems to be a better idea maybe.

I had a feeling it would be too small, (i havent seen one) hence why building a small box, so if a pod is illegal, then a partition is illegal too, so we have to put a lid on it?

sewid Grand Master

sewid

Posted
Posted
Originally posted by Robo's

I had a feeling it would be too small, (i havent seen one)  hence why building a small box, so if a pod is illegal, then a partition is illegal too, so we have to put a lid on it?

It's not illegal because it lacks a lid, it's illegal due to the EPA restrictions. That is it's too noisy (induction noise and the like) and the changes in emissions which may occur due to the changed intake.

Putting a lid on it is a way to lower the probability the cops are gonna defect you for it during an under bonnet inspection, but if they heard a blow off valve type noise from your car they probably wont know/care where it came from.

Cops seem to think that "blow off valves" are illegal tools of the devil. I would like to know if many of them actually know theyre just another part of a standard proper turbo car setup.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...