Jump to content
SAU Community

Recommended Posts

The car has a gloss black vinyl wrap on the Bonnet, A pillars, Roof and C Pillars back, Carbon fiber look alike wrapped B pillars, as well as a black Series 2 boot and wing (it just dosent show up very well in photos), The pod filter is mounted to the chassis using a bracket and has a CAI directly beneath it as shown in the pics. Also has the compulsary ridiculasly loud aftermarket exhaust, a set of TEIN HA coilovers and a full set of blue nolathane bushes :)

I know its not the quickest car in a straight line, but its mine and untill im off my P's this will satisfy my love of shiny things lol

Edited by Nikk_666

joker's r34 i was making fun of the carbon fiber on your dash and usb stick but then i saw it on the ambi pur and just lost it. i have the same ambi pur and laughed so hard and all is well insted of poking fun im goin to say job well done.

:cheers:

post-89457-0-83272300-1323084915_thumb.jpg

Hey everyone, i just bought this 1995 R33 GTS, pretty much stock apart from ROH rims. thoughts??

Looks in good nik, i highly suggest your restore the headlights look around at the methods there are kits you can get or use very fine Sandpaper to get it clear again. Stock is the way to go keep it like that just play around with Height, Rims and Exhaust !!!.

MY 95 R33 SKYLINE N/A (CURRENTLY IMPOUNDED) WAS MY DAILY FOR THE 5 DAYS I MANAGED TO HANG ONTO IT

IMG_0797.jpg

AND MY 96 180SX TYPE X SHELL RUNNING A SR20DE, MY CURRENT DAILY

IMG_075818-32-38.jpg

Edited by IMPORTS ONLY

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...