Jump to content
SAU Community

Recommended Posts

  Adriano said:
About the only thing that will make the car make boost in neutral like that is a skipped timing belt, retarding the cam and ignition timing.

Okay, got the mechanic to change the timing belt and this did not solve the problem. He said that it did not skip a tooth and all marks line up (found out that it has Toda branded adjustable intake and exhaust cam pulleys). He then disconnected the exhaust at the Cat converter and when revving it out of gear it did not make quite so much boost. We took it for a drive with it disconnected but the same problem was still there. The mechanic said that it feels if there is a blockage somewhere in the intake. While driving the car it was coming on to full boost at 3000rpm but is struggling to get there.

Things that have been checked so far;

turbo's spin freely,

cat converter is not blocked,

compression tested with all cylinders passing,

spark plugs are fine (the car does not missfire),

This problem is proving difficult to find, I am hoping someone out there might have some more suggestions on what could be causing all of this.

DSF

i would try a set of AFM and ecu if you can swap them with somone, so you know there good AFM problems usally limit car to 2000rpm or below. Also a backfire can damage the hot wire in the AFM.

Is it overfuling whith no load (in neautral), do have black smoke out the exhaust? what rpm can you get when free reving? are you still getting boost in neautral when the engine is cold?

cheers

  WHT11 said:
DSF

i would try a set of AFM and ecu if you can swap them with somone, so you know there good AFM problems usally limit car to 2000rpm or below. Also a backfire can damage the hot wire in the AFM.

Is it overfuling whith no load (in neautral), do have black smoke out the exhaust? what rpm can you get when free reving? are you still getting boost in neautral when the engine is cold?

cheers

Yes it is overfuelling with no load, with plenty of black sooty smoke.

At this stage while in neutral I am not confident in revving past the 4500rpm as it is hitting mas boost before that (though I have taken it past 6000rpm once).

All symptoms are the same whether the engine is cold or warmed up.

I have two spare AFMs (working conditions uncertain) but changing them over has not improved the engine problem so far.

Cheers.

Well the mechanic reckons that it is a possible sticky/faulty BOV. No the problem is intermittent as we were able to drive it normally for a little while, and now when driving anywhere between 4000-5500rpm it will dump all boost. Only change was the mechanic blowing pressure from the intake of the intercooler up to the plenum chamber.

Would a possible faulty OV be the cause of all of this? I am hoping this is it and all will be fixed.

  neo32 said:
i will check all sensors sounds like its in lime mode like when u unplug a afm etc so be checking voltages from sensors

But I thought that the ECU will not let you rev past 2000rpm when in limp mode? At the moment the car is running fine except when you get anywhere between 4000-5500rpm, where it cuts all boost/timing/fuel/whatever I am not sure but once it is below 4000rpm it runs fine.

I have been searching other posts, I found one where the symptoms are similar and the possible fault is either BOV's or the boost solenoid.

Cheers :)

Hey I reckon your problem would be a blocked vac line.

I say this because I have the same car, same prob exaxtly

(blew hose than had more probs later) checked everything.

Found a dead vac line on the very bottom of the intake plenum,

closest to the firewall.

Dont know the best way to unblock this one as it was inside the plenum(not the line itself)

So I just gave a quick blow in the line with an air compressor, and its been fine since.

Hope this helps

Jason

i cant explain the overboosting but my car hesitated to go past 2500 rpm and stalled on idle, soldered up the afms and its fine now, try finding a working set of afms to test it, no point using dodgy afms to test if ur afms work or not

sory mate didint read the page 2 posts

  DSF said:
But I thought that the ECU will not let you rev past 2000rpm when in limp mode? At the moment the car is running fine except when you get anywhere between 4000-5500rpm, where it cuts all boost/timing/fuel/whatever I am not sure but once it is below 4000rpm it runs fine.

I have been searching other posts, I found one where the symptoms are similar and the possible fault is either BOV's or the boost solenoid.

Cheers :D

It might not be the AFMs themselves but a problem in the plug or wiring. I had similar problem when i first got my car and swapped my ARF with known working ones, but the problem was still there so i ruled them out. It turned out to be a problem in the wiring causing one ARF to intermittently drop in voltage, thus causing the stalling/rough running. I rewired both my AFM and have never had a problem since.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The values for HID colour are also defined ~ see https://www.legislation.gov.au/F2006L02732/latest/text  ~ goto section 3.9 onwards ....
    • So, if the headlights' cutoff behaviour (angles, heights, etc) are not as per 6.2.6.1.1 without automatic levelling, then you have to have to have automatic** levelling. Also, if the headlight does not have the required markings, then neither automatic nor manual adjusters are going to be acceptable. That's because the base headlight itself does not meet the minimum requirement (which is the marking). ** with the option of manual levelling, if the headlight otherwise meets the same requirements as for the automatic case AND can be set to the "base" alignment at the headlight itself. So that's an additional requirement for the manual case. So, provided that the marking is on the headlight and there is a local manual adjustment back to "base" on the headlight, then yes, you could argue that they are code compliant. But if you are missing any single one of these things, then they are not. And unlike certain other standards that I work with, there does not seem to be scope to prepare a "fitness for purpose" report. Well, I guess there actually is. You might engage an automotive engineer to write a report stating that the lights meet the performance requirements of the standard even if they are missing, for example, the markings.  
    • Vertical orientation   6.2.6.1.1. The initial downward inclination of the cut off of the dipped-beam to be set in the unladen vehicle state with one person in the driver's seat shall be specified within an accuracy of 0.1 per cent by the manufacturer and indicated in a clearly legible and indelible manner on each vehicle close to either headlamp or the manufacturer's plate by the symbol shown in Annex 7.   The value of this indicated downward inclination shall be defined in accordance with paragraph 6.2.6.1.2.   6.2.6.1.2. Depending on the mounting height in metres (h) of the lower edge of the apparent surface in the direction of the reference axis of the dipped beam headlamp, measured on the unladen vehicles, the vertical inclination of the cut off of the dipped- beam shall, under all the static conditions of Annex 5, remain between the following limits and the initial aiming shall have the following values:   h < 0.8   Limits: between 0.5 per cent and 2.5 per cent   Initial aiming: between 1.0 per cent and 1.5 per cent   0.8 < h < 1.0   Limits: between 0.5 per cent and 2.5 per cent   Initial aiming: between 1.0 per cent and 1.5 per cent   Or, at the discretion of the manufacturer,   Limits: between 1.0 per cent and 3.0 per cent   Initial aiming: between 1.5 per cent and 2.0 per cent   The application for the vehicle type approval shall, in this case, contain information as to which of the two alternatives is to be used.   h > 1.0   Limits: between 1.0 per cent and 3.0 per cent   Initial aiming: between 1.5 per cent and 2.0 per cent   The above limits and the initial aiming values are summarized in the diagram below.   For category N3G (off-road) vehicles where the headlamps exceed a height of 1,200 mm, the limits for the vertical inclination of the cut-off shall be between: -1.5 per cent and -3.5 per cent.   The initial aim shall be set between: -2 per cent and -2.5 per cent.
×
×
  • Create New...