Jump to content
SAU Community

Recommended Posts

Hey guys, cos im lazy, and i don't wanna look at the phone book, and cos i want your experiences,

i wanna know where there are jap wreckers in perth, and your personal experiences with them

the only 1 i can think of off the top of my head is in welshpool near where i used to work, on Pilbara st i think... not to sure, don't remember what its called:rolleyes:

looking for a few little bits n pieces

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/
Share on other sites

hey memphis, i need driver side door pillar thingy(between the driver mirror and the rear quarter mirror), mine got ripped off when some guy tried to break into my car (good thing i have metal sleeved tint)

hope u can ask them for me, my number is 0401290390,pls give me a sms

Aidwin

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-458597
Share on other sites

jap motor sport in sydney and just jap in adelaide are both very good and will post most things over including frieght cheaper than any company in perth could sell it to you.The only other person you mite want to try is Mayhem on this site as he sometimes brings in half cuts.hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-460573
Share on other sites

In cannington there is japwreck and Nispart Datpart I am not sure of addresses. One is near bunnings, the other near the big WA salvage. For common older stuff Niss part but Japwreck have engines mirrors front cuts strut bars etc etc.

Actually the most helpful cos i needed some small plastic wiper box screws was pulsarwreck around the corner for nisspart.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-461040
Share on other sites

  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...