Jump to content
SAU Community

Recommended Posts

Hey guys, cos im lazy, and i don't wanna look at the phone book, and cos i want your experiences,

i wanna know where there are jap wreckers in perth, and your personal experiences with them

the only 1 i can think of off the top of my head is in welshpool near where i used to work, on Pilbara st i think... not to sure, don't remember what its called:rolleyes:

looking for a few little bits n pieces

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/
Share on other sites

hey memphis, i need driver side door pillar thingy(between the driver mirror and the rear quarter mirror), mine got ripped off when some guy tried to break into my car (good thing i have metal sleeved tint)

hope u can ask them for me, my number is 0401290390,pls give me a sms

Aidwin

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-458597
Share on other sites

jap motor sport in sydney and just jap in adelaide are both very good and will post most things over including frieght cheaper than any company in perth could sell it to you.The only other person you mite want to try is Mayhem on this site as he sometimes brings in half cuts.hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-460573
Share on other sites

In cannington there is japwreck and Nispart Datpart I am not sure of addresses. One is near bunnings, the other near the big WA salvage. For common older stuff Niss part but Japwreck have engines mirrors front cuts strut bars etc etc.

Actually the most helpful cos i needed some small plastic wiper box screws was pulsarwreck around the corner for nisspart.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-461040
Share on other sites

  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...