Jump to content
SAU Community

Recommended Posts

Hi guys I am currently organise a group of 5 people to purchasing the In Dash DVD Player with 7" Auto Color Monitor.

Features:

The DVD Player

DVD , Didital Video Disc, MP3, CD, CD-R, CD-RW, AM/FM Radio (Can Listen all Local Channel)

Also it comes with English Instruction, Remote Control, USB Ram and SD Card Input as well!!

The Monitor:

It can support PAL & NTSC, 16:9 & 4:3, also can connect to GPS system and parking sensor with parking video

Full auto up and down and it comes with Remote Control

Price of each system is $310 pick up from BRISBANE

Please put down your name if you interest

Group buying will be end 30/05/2008

post-43873-1209375029_thumb.jpg

could you get any more pictures?, also would you post this to sydney?

yes will post some more pic tomorrow when i put one into my car!! And can send to sydney!! About $25 for postage

  • 2 weeks later...
  • 1 month later...
  • 2 weeks later...

yep I am looking for double din touch screen too. I currently have a $300 Eonon one off Ebay that blew up after about a year (very heavy use in that time though). Problem is that these cheap Chinese ones tend to have clunky menus, and controls. Also the radio station and TV receivers tend to have very poor amps built-in - so radio and TV reception is fairly crap.

But a touch screen one with a decent GUI and decent AMP would be awesome. Oh, and a tip for new guys - don't bother trying to get in-car TV to work - it just plain sucks unless you are next to a broadcasting tower. Of course we are looking to pay $400ish for such a thing.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...