Jump to content
SAU Community

Recommended Posts

Alright I was just wondering what is the leanest afr you guys would consider safe. Basically I have a stock rb26 with no boost restrictor, exhaust and a FMIC, so the boost is around 15psi. had the car on a dyno and the afr ratio was mostly in the high 11s and low 12s but spiked at about 12.9. Is this getting pretty dangerously lean? Thanks for any help. Also what AFR would you recommend tuning to when I get PFC?

Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/
Share on other sites

As NYTSKY said you 11.8 is safe! Don't risk it with 12.9!! I know many tuners that tune with afrs like yours but it is risky and to have many horsepower!

Better safe than sorry!

If you have with 15psi 12.9, try 12psi or less!!

Better safe than sorry!

Buy a PFC or remap your stock ecu. It is cheaper than to rebuild your engine!!

Better safe than sorry!

:rofl:

Edited by GreeceS13
Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3835250
Share on other sites

So the stock injectors should be good enough to keep up with the 15psi? Also is anyone sure what the boost is without the boost restrictor on a GTR? My car is swapped so I am not positive that the turbos are stock, since i got the motor with 30k on it. though I am pretty sure cause they appear to be stock. Also yes it is a stock computer. Fuel pump is a walbro 255lph so I would think it would be fine. I am gonna get it back on the dyno in a couple weeks and take another look at the afr.

Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3838430
Share on other sites

A print out of the dyno sheet... power vs AFR & power vs boost would be able to tell me if its dangerous or not. The first one would help if thats all you have.

Alright I was just wondering what is the leanest afr you guys would consider safe. Basically I have a stock rb26 with no boost restrictor, exhaust and a FMIC, so the boost is around 15psi. had the car on a dyno and the afr ratio was mostly in the high 11s and low 12s but spiked at about 12.9. Is this getting pretty dangerously lean? Thanks for any help. Also what AFR would you recommend tuning to when I get PFC?
Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3838453
Share on other sites

  • 1 month later...
A print out of the dyno sheet... power vs AFR & power vs boost would be able to tell me if its dangerous or not. The first one would help if thats all you have.

I will post a dyno sheet when if i can get ahold of one. Also what should the stock wastegate boost pressure be for the stock turbos? my car is boosting between 15 and 18psi. seems like that is higher than it should be.

Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3945598
Share on other sites

12.9 isnt dangerous if you have timing to match, which out of a stock ECU shouldnt be too bad, but still dont drive it hard, i'd get it tuned properly first. that said i have seen cars (R34 GTR is the first one that comes to mind) that came out of racepace and was on a dyno elsewhere, its A:F ratio was 13:1 up top, and i believe thats just how it was tuned. i quizzed the dyno operator on it and said he'd seen it a few times from racepace adn it works fine, just less margin of error for crap fuel etc.

point is, i wouldnt say its bad if racepace is doing it (that said i could be entirely wrong lol)

Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3947297
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...