Jump to content
SAU Community

Safe Afr

BlackRBS13

By BlackRBS13,
in Engines & Forced Induction

 Share

Recommended Posts

BlackRBS13 Contributor

BlackRBS13

Posted
Posted

Alright I was just wondering what is the leanest afr you guys would consider safe. Basically I have a stock rb26 with no boost restrictor, exhaust and a FMIC, so the boost is around 15psi. had the car on a dyno and the afr ratio was mostly in the high 11s and low 12s but spiked at about 12.9. Is this getting pretty dangerously lean? Thanks for any help. Also what AFR would you recommend tuning to when I get PFC?

Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/
Share on other sites
GreeceS13 Rising Star

GreeceS13

Posted
Posted (edited)

As NYTSKY said you 11.8 is safe! Don't risk it with 12.9!! I know many tuners that tune with afrs like yours but it is risky and to have many horsepower!

Better safe than sorry!

If you have with 15psi 12.9, try 12psi or less!!

Better safe than sorry!

Buy a PFC or remap your stock ecu. It is cheaper than to rebuild your engine!!

Better safe than sorry!

:rofl:

Edited by GreeceS13
Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3835250
Share on other sites
BlackRBS13 Contributor

BlackRBS13

Posted
  • Author
Posted

So the stock injectors should be good enough to keep up with the 15psi? Also is anyone sure what the boost is without the boost restrictor on a GTR? My car is swapped so I am not positive that the turbos are stock, since i got the motor with 30k on it. though I am pretty sure cause they appear to be stock. Also yes it is a stock computer. Fuel pump is a walbro 255lph so I would think it would be fine. I am gonna get it back on the dyno in a couple weeks and take another look at the afr.

Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3838430
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

A print out of the dyno sheet... power vs AFR & power vs boost would be able to tell me if its dangerous or not. The first one would help if thats all you have.

Alright I was just wondering what is the leanest afr you guys would consider safe. Basically I have a stock rb26 with no boost restrictor, exhaust and a FMIC, so the boost is around 15psi. had the car on a dyno and the afr ratio was mostly in the high 11s and low 12s but spiked at about 12.9. Is this getting pretty dangerously lean? Thanks for any help. Also what AFR would you recommend tuning to when I get PFC?
Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3838453
Share on other sites
  • 1 month later...
BlackRBS13 Contributor

BlackRBS13

Posted
  • Author
Posted
A print out of the dyno sheet... power vs AFR & power vs boost would be able to tell me if its dangerous or not. The first one would help if thats all you have.

I will post a dyno sheet when if i can get ahold of one. Also what should the stock wastegate boost pressure be for the stock turbos? my car is boosting between 15 and 18psi. seems like that is higher than it should be.

Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3945598
Share on other sites
VB- Veteran

VB-

Posted
Posted

12.9 isnt dangerous if you have timing to match, which out of a stock ECU shouldnt be too bad, but still dont drive it hard, i'd get it tuned properly first. that said i have seen cars (R34 GTR is the first one that comes to mind) that came out of racepace and was on a dyno elsewhere, its A:F ratio was 13:1 up top, and i believe thats just how it was tuned. i quizzed the dyno operator on it and said he'd seen it a few times from racepace adn it works fine, just less margin of error for crap fuel etc.

point is, i wouldnt say its bad if racepace is doing it (that said i could be entirely wrong lol)

Link to comment
https://www.sau.com.au/forums/topic/217188-safe-afr/#findComment-3947297
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...