Jump to content
SAU Community

Recommended Posts

Hi all.

I currently have a RB30 bock and looking to build this up with a RB26 head, so i can run twins on there.

Still haven't started anything yet, but just about to get the block checked out to make sure its worth using.

I not going for the forged pistons/rods unless i have too, i.e if the block is worn. Plus i don't want massive power, as i have a RB20DET in my 32, so this build should be more then enough.

So far my shopping list/plans for my build.

-Block-

ACL Bearings

ARP Rod Bolts

N1 Pump

Oil crank coller

-Head-

Standard RB26 head, inlet plenum.

Aftermarket exhaust manifolds.

-Turbos-

Still not sure which ones yet, need to do more homework, but something like the disco potatoes but a little bit bigger.

Already have a Nismo Fuel pump and a RPS Paddle clutch, i will have to replace my gearbox soon as its making for too much noise in all gears, lol, So i will fit a R33 Large casting box.

Am i missing or doing anything wrong for this build?

Cheers

Edited by rb30inside
Link to comment
https://www.sau.com.au/forums/topic/219762-rb30-26dett-build/
Share on other sites

I agree with Adriano on this one, many ppl swear by the standard manifolds with a little work.

I think you need to work out your power goals, you sad you don't want massive power, but your talking disco potatoes x2... single dp turbos make pretty potent power, let alone two of the suckers.

If you end up sticking with the stock manifolds, Id look at the HKS turbo kits like the GTSS, which are bolt and have all fittings,gaskets etc(unlike their Garret counterparts).

One thing to keep in mind is , how much you want to rev the motor.

I would look into a H/balancer if you want to spin it over 7000rpm.

I had a stock RB30 (new) one on my setup. Once it got over 7500+rpm is was spinning on the the crank.

I went a rolla master one and its hitting 9500rpm all day!!!!

Keep it in mind..

One thing to keep in mind is , how much you want to rev the motor.

I would look into a H/balancer if you want to spin it over 7000rpm.

I had a stock RB30 (new) one on my setup. Once it got over 7500+rpm is was spinning on the the crank.

I went a rolla master one and its hitting 9500rpm all day!!!!

Keep it in mind..

9500rpm??? i have spend over 18,000 on my long motor, so are you saying i can rev mine all day to 9500rpm??

spinning on the crank??? mate there is a keyway on the crank... unless you forgot to install it there is no way you would spin the balancer on the crank...

The Key way wasn't holding on my setup.

Also if you spent 18,000 on a long motor , some one is and has taken you for a ride.

lol, no1 is taking me for a ride champ, actually ive been taken care of, eg. OS Giken RB30 $22,500

OS Giken RB31 $24,000

thats just for the bottom end, dissasembled. with no oil pump or sump, even though mine is not a os setup, it will produce the same if not more than that, ive used a special block and there is around 4500 bucks in block prep just for the particular one ive used...... so, it adds up easily

also key ways dont fall out as easy as you think, its got nowhere to fall to

Edited by den001

den001...im jealous you used the diesel 28block....i would love to see pics of the mods needed to make that work with a rb head.

9500rpm...mate sure your tacho aint broke! You must have lots of money to spend, you realise wear and tear increases at a stupid rate the more you rev the thing?

Sounds good, although IMO instead of spending money on exhaust manifolds that make stuff all difference, i would fit some forged pistons. The arp rod bolts only come in packs of 8 so you need 2 packs. I have a 1/2 pack if you interested.

I will could be interested in these.

PM me a price.

I agree with Adriano on this one, many ppl swear by the standard manifolds with a little work.

I think you need to work out your power goals, you sad you don't want massive power, but your talking disco potatoes x2... single dp turbos make pretty potent power, let alone two of the suckers.

If you end up sticking with the stock manifolds, Id look at the HKS turbo kits like the GTSS, which are bolt and have all fittings,gaskets etc(unlike their Garret counterparts).

Point taken about the manifolds.

I would like to see 500whp

One thing to keep in mind is , how much you want to rev the motor.

Yeah, i not after a laggy piece of shit, i want low end power so 7000rpm limit is fine for me.

What size of injectors do you recon i should look at? will the nismo fuel pump be fine?

Cheers

put forgies in there if your wanting 500rwhp... do it right the first time :)

I have been thinking about this and i would like to wait till spool imports do there stroker kit before i fit forged internals.

Does anyone have any good info on fitting the right size ALC bearings?

Cheers

I have been thinking about this and i would like to wait till spool imports do there stroker kit before i fit forged internals.

Does anyone have any good info on fitting the right size ALC bearings?

Cheers

strip the block and take it to an engine rebuilder who's familiar with the rb head conversions....the reason i say this is so they know that the block they are refacing is going to be under more pressure than it originally was.

like in my case they bored the main bearing tunnel and polished back the crank while balancing it..... used oversize bearings

they bores we're still within factory spec after 350,000 kms but but the pistons looked shagged so they went in favour of forgies. with a regrind down the bores aswell.

this is why ya dont buy ya bearings till the engine rebuilder has told ya what needs doing to it....saves running round town wasting time.

for the power level you want to run, you dont need to get oil squiters installed into the block, dont waste your money,

if you really want oil squiters you must run a diesel block, it will be expensive to get to properly modified to incorporate a twin cam head...

  • 7 months later...

Well guys i have been rather lazy since i got the block been down the pub every night!!!!

Anyway. i have decided to go for a big single turbo not the twins. So now the build will be.

RB30 balanced bottom end

RB26 head with 3 angle valve seats

Holset HX40 turbo with external wastegate

Spool rods and CP flattop pistons

ARP bolts and ACL bearings

Standard GTR intake

Ross dampener

N1 oil pump

How does that sound so far?

Now i need help on.

Is it worth getting different cams?

How thick do i need my head gasket to be?

Anything i have forgotten or over kill?

Put some high lift 260deg cams in the head and while they're at it get them to port it

Why the change to a single? Ive gone from single to twins and love them :)

N1 oil pump is ok, dont forget crank collar to suit

Cam gears are a worthwhile addition

N1 water pump

No oil squirters needed

Larger sump is good insurance but not 100% needed with that oil pump

ARP head studs, again, insurance but can be left off if you have a budget

I must've missed it - is this into a GTR or GTST?

Are you building this yourself or getting a workshop to do it?

Put some high lift 260deg cams in the head and while they're at it get them to port it

Yeah, im thinking about cams, need to do more homework on them.

Why the change to a single? Ive gone from single to twins and love them :)

More easy of use and save a bit of money.

N1 oil pump is ok, dont forget crank collar to suit

Yeah, i haven't forgotten about that.

Cam gears are a worthwhile addition

If i change the cams i will.

N1 water pump

Really worth the change??

No oil squirters needed

Yeah i was going to scrimp on these, seem a lot of hassle to get them fitted

Larger sump is good insurance but not 100% needed with that oil pump

Did't think about this. Might give this a miss just to save a bit more money

ARP head studs, again, insurance but can be left off if you have a budget

Don't have a budget, but im not loaded at the same time, just going to buy bits every month till i have everything i need, lol

I must've missed it - is this into a GTR or GTST?

R32 GTST Gun metal grey. I should post some pics some time, lol

Are you building this yourself or getting a workshop to do it?

Im going to do most of it myself, but going to get the right people to build the head so i can just bolt it on.

So how can i find out what size injectors i need?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...