Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

hey guys, i lost my rays lock nut key today. I think i left it on the nut and it must have fallen out while driving. How stupid can i be lol

I know not all lock nuts are the same. The key i got has 7 sides and on one side it has a little slot to go in. If someone has one to lend or knows where i can get one that'll be very good

Cheers :)

  • 3 weeks later...
  • 2 weeks later...

wanted to borrow: spring compressors to remove coilovers

PM me

If there coilovers just undo the bottom 2 lock rings and wind thw spring down. That will shorten them enough to get them out. Or use some leverage to pull your suspension arms down and slide it off the bolt.

  • 2 weeks later...

in need of a 27 mm socket nd a cranksharft pulley asap. nd would be better if someone can drop off to north east suburbs (Royston Park). be willing to give $50 if anyone is able to do it tonight. message me on 0405504778.

  • 4 weeks later...

krishy, get a plate of metal, cut it to the size of a flange, drill 5 holes in it, put it inbetween where your exhaust joins, instant quiet. do not boost, remove after regency.

I thought about that, might give that a go first to see if it does quiten it down. Its pretty loud as is, which is why I am afraid it won't go below the legal limit.

I thought about that, might give that a go first to see if it does quiten it down. Its pretty loud as is, which is why I am afraid it won't go below the legal limit.

i got ben from jms to put a baffle plate in my exhaust

it was beyond quiet

:)

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
    • Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
×
×
  • Create New...