Jump to content
SAU Community

Recommended Posts

If they get you to do an emissions test its easy, otherwise on visual inspection i think its pretty hard.

But my thoughts are dont do it. A good 3" cat will flow well and is legal. Some things we cant avoid like running re-written ECUs and aftermarket ECUs.

Then there is the shady topic of legaility concerning BOVs/Filters/Intercooler etc etc, but one thing we can do is run cats on our road cars.

Link to comment
https://www.sau.com.au/forums/topic/22109-cats/#findComment-472834
Share on other sites

Guest INASNT
Originally posted by akeenan

you can put a straight pipe where the cat is and the shell of the cat round the pipe and make it look authentic.

when u go for a epa test they stick a probe near the cat and can tell if its working properly.

But think about it would u rather have that extra 5kw or be able to breath clean air???

Link to comment
https://www.sau.com.au/forums/topic/22109-cats/#findComment-473008
Share on other sites

i had a cat-out pipe for a while. It will spool the turbo faster, but doesn't really do much for emissions. You are likely to only gain about 2-5rwkW so bugger it. And a gutted cat will likely flow worse than a hi-flow and hence make less power; as has been said it slows the velocity of the exhaust and causes more turbulence around the empty cat.

Just get a highflow from BATMBL and be done with it - i have and am very happy with it.

Link to comment
https://www.sau.com.au/forums/topic/22109-cats/#findComment-474070
Share on other sites

Dunno about the cops, but I reckon the RSPCA would be onto you.....

seriously though, Why do it? its cheaper than a high flow cat, granted, but I doubt there would even be a noticeable increase over a healthy cat convertor. A clogged one would be a restriction though, but a healthy, fresh one , in a decent size, would be a negligible benefit

Link to comment
https://www.sau.com.au/forums/topic/22109-cats/#findComment-474336
Share on other sites

My motorcycle didn't come with a cat, and it's not legally required to have one on there. I don't actually know why, because the bike requires premium (toxic) fuel as well, so in theory it should have come with a cat. Strange.

Link to comment
https://www.sau.com.au/forums/topic/22109-cats/#findComment-475438
Share on other sites

Cats do fit on bikes. The current model VFR800 has one for a couple of years now (since 2001 I think) and it fits well enough (just smaller than a car one). A few other models have them too, like the Gold Wing.

In California I think all new motorcycles are required to have them. A trend that will probably follow elsewhere.

Link to comment
https://www.sau.com.au/forums/topic/22109-cats/#findComment-475913
Share on other sites

I actually wonder what happened to the old rotten egg gas smell that unleaded cars used to get. It doesn't seem to happen anymore. They must have removed a lot of sulfur from fuels.

As for motorcycle cats, I think as long as the general population and the politicians remain ignorant as to just how polluting motorcycles are (especially 2 strokes) then we won't be forced to put them on just yet :P

Link to comment
https://www.sau.com.au/forums/topic/22109-cats/#findComment-475941
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...