Jump to content
SAU Community

Tuning Your Car

mlyf16

By mlyf16,
in Victoria

 Share

Recommended Posts

SABBAi Grand Master

SABBAi

Posted
Posted

I believe the LM-01 has the ability to simulate narrow band outputs. You could do that. However, Most wide band do not like excessive heat, unlike their narrow band brothers, and can foul up easily. I would suggest that you weld in a second O2 bung midway between the turbo and the cat. This way you will not get incorrect readings from the sensor getting too hot, and falling out of calibration, nor will you get a delayed readout from having a sniffer tube up the exhaust pipe.

Recalibration of the wideband sensors can be done by yourself, but it is time consuming. They are something that you use for tuning, etc and remove as the sensors can be damaged if they are used continually like the narrowbands.

Hope that helps.

Link to comment
https://www.sau.com.au/forums/topic/221767-tuning-your-car/#findComment-3909692
Share on other sites
ziad Community Regular

ziad

Posted
Posted

evo DIY tuning FTW :D i have an innovate LC-1 no

put the sensor about 1 meter from the turbo but before the cat (as the cat will change the reading slightly).

a bung will need to be welded to put the sensor, and it has to be between 10 and 2 O clock position.

recalibration takes about 1-2 mins... but best to pull the sensor out of the exhaust so that it calibrates from clean air, taking the sensor out will take longer as you may need to jack the car up. recalibration only needs to be done approx 2 times a year at the max, for a turbo daily driven car.

keep the sensor powered all the times the car is running.

on a cold/humid morning do not keep the ign (sensor powered) while the car is not running.

once installed and as long as you obey the above instructions the sensor can last for a couple of years without problem in a daily driven car.

buy one from the states, due to aussie dollar it should cost about $250-300 to get one delivered.... depending on dyno prices it might just be cheaper to get proper dyno time than an LC1. unless you are inclined to fiddle a lot. plus the sensors are a little fragile and can die.

EDIT: just found that the LM1 will be supersceeded by LM2 so currently you can pickup a new LM1 for $280USD plus postage.

http://tunertools.com/proddetail.asp?prod=IN-3723

Link to comment
https://www.sau.com.au/forums/topic/221767-tuning-your-car/#findComment-3913537
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...