Jump to content
SAU Community

hit pothole and buckled rim, can i sue the council?


Recommended Posts

hey guys,

as the title says i hit this massive pothole on the edge of the road (another car was coming so i had to go right to the edge) and heard a massive bang. i jacked my car up when i got home and the rim is clearly buckled.

if i take a photo of the pothole, take a photo of my buckled rim and send it to the council, do you think they will pay for a new rim or repair costs of my existing rim??? or will they contest it and take me to court and it would end up being more trouble than its worth?

thanks

greg

look the local councils will screw you around till your like...180 years old. hahaha, bunch of pricks, they will say, call this person, then that person and it will happen prolly, but only after a lot of mental anguish on your behalf. By all means try and good luck to you man, just warning ya that stupid shit WILL happen

Dave

Guest RedLineGTR

"On a serious" note. have some pot holes around my area, and i try and miss them but sometimes you just cant when the wheel "falls" into the hole i feel that it's damaging my suspension and if i find out if something farks up i'm sure to go to the counsil and make something off it. I just might write them a letter when i get a sec to see if they can fix it. Cheers Rob

lawyers letter will fix up that problem.. threaten them loss of income due to loss of vehicle for time its off the road, repair of rim, and anguish due to destroyed rim. Write intelligently enough and you will get it through. BTW: take photos of said scene, damage to said wheel, and make it more than obvious it was their ****ing fault basically..

Its happened plenty of times before with rich ppl suing the council for damage to their nice rich cars .esp brighton, glen iris, camberwell, toorak, et al area . Notice how the roads around those areas are much nicer than the outer suburbs? funny that

thanks for your help everyone, i'll take lots of pics tomorrow, write up a formal and intelligent letter and see what comes of it. I don't think it would be worth the lawyer's fees and the hassles to get a lawyers letter sent to the council. i keep you updated on how things go.

anyone know any places to get my rim repaired in eastern suburbs?

lol@dan_the_man...i know what u mean, these days people seem to be suing because they didn't like the way someone looked at them. that case in the US (where else?) where some guys sued McDonalds because they sell fattening food was a prime example of how ridiculous things have become with litigation.

dont think so dude, you dnt have a leg to stand on, its the ****ing government ffs, basically when u sign your registration/licence it says stuff in the conditions like 'you accept all risks that personal injury/death/property damage blah blah to you and your car may ocur if you drive on the roads yada yada... they arent that stupid, otherwise noone would pay to get their car fixed... if someone hits you instead of sueing them u could sue the concil for giving such an idiot driver a licence... cmon man there's limits, as harsh as it is i suggest u dont waste your time and just get da rim repaired/new rims and be on your way nice n happy

btw ive just spent 2 months waiting for money form the guy who hit me... my cars has panel damage since and its ugly... i just spoke to a lawyer as things havent gotten very far and he basically told me there's nothing i can do for such a small amount, its just not worth it, and he said if the other party went to a lawyer the lawyer would have told them dont bother paying coz there's not much chan cei will take him to court etc...

moral of the story, lifes a bitch, ignore the bad times ;)

That's f**ked Nath, sorry to hear!

Greg, i have heard stories of people successfully getting money for damage to their cars, but you may have to prove that the council was neglegent and failed to address a road hazard, VERY hard to do.

you can sue concil.

you pay rates/rego blah blah to have the roads in a USEABLE condition.

If you split a $2000 wheel... or a $5 one, you can sue them for it.

get a nice letter draw up. Photos etc as others have said.

And they should pay.

If not, got them to court. The court will rule in your favour as potholes should NOT be there.

yewr but going to court with help will cost at lkeast $1300 (as i was instructed in my incident).. so its deinfitely not worth it, because even if u sue as well for your own legal fees there are still plenty of fees that the court doesnt consider the need of the other partty to pay so in the end if the claim your making is not at least $2000 then dont bother goingt to court.. this is what the lawyer told me for future reference

yer he workjed it out even if i represent myself, ill actually only get $200 max form the guy in my case coz there are still fees, its not worth it unloess its $2000 he said... stuff it im not wasting my time anymore, the ****er can be a ****er and we'll see what happens ;)

Guest INASNT

U don't sue the council...u sue ***in Vic Roads!!!

There the ones who build our roads so its only right that u sue there asses!!!!

The same shit happened to my girlfriends mum...in her shitty little festiva on punt rd. she made an entry at the police st then forwarded it to vic roads who re-inbursed her for the new tyre and costs to get a wheel allignment.

Man if it could happen to her then they would prob do the came thing for u!!

DJ_L3ThAL

A bloke slightly hit my old 300ZX. $220 worth damage. Told me to get fuc$ed - he wasn't paying. I took him to small claims court. Cost $90.

Judge got right up him. He paid my $220 + my $90. Excellent. I kept the cash and sold the 300 and the rest is history... :-)

Ok let me clarify the sueing issue for you.

Local council look after maintenance on roads even though vic roads are the governing body for road location and type.

Its completely in your rights to seak compensation for property damage due to poor quality or poorly maintained surfaces, but the problem lies in developing blame.

To lodge a sucessful claim or to win in a court case you need to prove that the council was negligent in either they're road construction or maintenance.

The problem here is that its near impossible to prove that it was they're fault that the pot hole developed. However if the pot-hole has been previously repaired and has yet again gone sour then you've got a start point. This proves that teh council have acknowledged that a problem exists and have put in place means to fix it which have failed. It is upon that failure that you have a basis for making a claim.

alternatively if you can prove that the council have been made aware of potential problem and have not responded in an acording manner then again you have a basis for negligence.

Finally if you're really out to screw them, you need to gather a group of people that can individually lodge a complaint to the council regarding the pot-hole and its potential danger to you vehciles safe driving. Then you need to allocate a suitable period of time to allow them to review all the complaints and then source a series of road repair agencies to see an approximate lead time for road repair.

With these in hand, you just wait out that time and then lodge your claim stating that the incident occured after that period and thus the council made no attempt to fix the problem that had already been brought to they're attention. However proving how you knew about the complaints might be a bit difficult.

GOOD LUCK!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...